Section 11-280.1-43 - Methods of release detection for tanksEach method of release detection for tanks used to meet the requirements of sections 11-280.1-40 to 11-280.1-42 must be conducted in accordance with the following:
(1) Inventory control. Product inventory control (or another test of equivalent performance) must be conducted monthly to detect a release of at least one percent of flow-through plus one hundred thirty gallons on a monthly basis in the following manner: (A) Inventory volume measurements for regulated substance inputs, withdrawals, and the amount still remaining in the tank are recorded each operating day;(B) The equipment used is capable of measuring the level of product over the full range of the tank's height to the nearest one-eighth of an inch;(C) If a manual measuring device is used (e.g., a gauge stick), the measurements must be made through a drop tube that extends to within one foot of the tank bottom. Level measurements shall be to the nearest one-eighth of an inch;(D) The regulated substance inputs are reconciled with delivery receipts by measurement of the tank inventory volume before and after delivery;(E) Deliveries are made through a drop tube that extends to within one foot of the tank bottom;(F) Product dispensing is metered and recorded within the state standards for meter calibration or an accuracy of six cubic inches for every five gallons of product withdrawn, and the meter is calibrated every three hundred sixty-five days; and(G) The measurement of any water level in the bottom of the tank is made to the nearest one-eighth of an inch at least once a month.(2) Manual tank gauging. Manual tank gauging must meet the following requirements: (A) Tank liquid level measurements are taken at the beginning and ending of a period using the appropriate minimum duration of test value in the table below during which no liquid is added to or removed from the tank;(B) If a manual measuring device is used (e.g., a gauge stick), the measurements must be made through a drop tube that extends to within one foot of the tank bottom. Level measurements shall be to the nearest one-eighth of an inch;(C) Level measurements are based on an average of two consecutive stick readings at both the beginning and ending of the period;(D) The equipment used is capable of measuring the level of product over the full range of the tank's height to the nearest one-eighth of an inch;(E) A release is suspected and subject to the requirements of subchapter 5 if the variation between beginning and ending measurements exceeds the weekly or monthly standards in the following table: Nominal lank capacity | Minimum duration of test | Weekly standard (one test) | Monthly standard (four test average) |
550 gallons or less ............................................................ | 36 hours........ | 10 gallons........ | 5 gallons |
551-1,000 gallons (when tank diameter is 64 inches)....................... | 44 hours........ | 9 gallons......... | 4 gallons |
551-1,000 gallons (when tank diameter is 48 inches).................. | 56 hours............. | 12 gallons........... | 6 gallons |
551-1,000 gallons (also requires periodic tank tightness testing) "..... | 36 hours.......... | 13 gallons.......... | 7 gallons |
1,001-2,000 gallons (also requ res periodic tank tightness testing).. | 36 hours............ | 26 gallons........ | 13 gallons |
(F) Tanks of five hundred fifty gallons or less nominal capacity and tanks with a nominal capacity of five hundred fifty-one to one thousand gallons that meet the tank diameter criteria in the table in subparagraph (E) may use manual tank gauging as the sole method of release detection. All other tanks with a nominal capacity of five hundred fifty-one to two thousand gallons may use manual tank gauging in place of inventory control in paragraph (1), combined with tank tightness testing as indicated in the table. Tanks of greater than two thousand gallons nominal capacity may not use this method to meet the requirements of this subchapter.(3) Tank tightness testing. Tank tightness testing (or another test of equivalent performance) must be capable of detecting a 0.1 gallon per hour leak rate from any portion of the tank that routinely contains product while accounting for the effects of thermal expansion or contraction of the product, vapor pockets, tank deformation, evaporation or condensation, and the location of the water table.(4) Automatic tank gauging. Equipment for automatic tank gauging that tests for the loss of product and conducts inventory control must meet the following requirements: (A) The automatic product level monitor test can detect a 0.2 gallon per hour leak rate from any portion of the tank that routinely contains product;(B) The automatic tank gauging equipment must meet the inventory control (or other test of equivalent performance) requirements of paragraph (1); and(C) The test must be performed with the system operating in one of the following modes: (i) In-tank static testing conducted at least once every thirty-one days; or (ii) Continuous in-tank leak detection operating on an uninterrupted basis or operating within a process that allows the system to gather incremental measurements to determine the leak status of the tank at least once every thirty-one days.(5) Vapor monitoring. Testing or monitoring for vapors within the soil gas of the excavation zone must meet the following requirements:(A) The materials used as backfill are sufficiently porous (e.g., gravel, sand, crushed rock) to readily allow diffusion of vapors from releases into the excavation area;(B) The stored regulated substance, or a tracer compound placed in the tank system, is sufficiently volatile (e.g., gasoline) to result in a vapor level that is detectable by the monitoring devices located in the excavation zone in the event of a release from the tank;(C) The measurement of vapors by the monitoring device is not rendered inoperative by the groundwater, rainfall, or soil moisture or other known interferences so that a release could go undetected for more than thirty-one days;(D) The level of background contamination in the excavation zone will not interfere with the method used to detect releases from the tank;(E) The vapor monitors are designed and operated to detect any significant increase in concentration above background of the regulated substance stored in the tank system, a component or components of that substance, or a tracer compound placed in the tank system;(F) In the UST excavation zone, the site is assessed to ensure compliance with the requirements in subparagraphs (A) to (D) and to establish the number and positioning of monitoring wells that will detect releases within the excavation zone from any portion of the tank that routinely contains product; and(G) Monitoring wells are clearly marked and secured to avoid unauthorized access and tampering.(6) Groundwater monitoring. Testing or monitoring for liquids on the groundwater must meet the following requirements: (A) The regulated substance stored is immiscible in water and has a specific gravity of less than one;(B) Groundwater is never more than twenty feet from the ground surface and the hydraulic conductivity of the soils between the UST system and the monitoring wells or devices is not less than 0.01 cm/sec (e.g., the soil should consist of gravels, coarse to medium sands, coarse silts or other permeable materials);(C) The slotted portion of the monitoring well casing must be designed to prevent migration of natural soils or filter pack into the well and to allow entry of regulated substance on the water table into the well under both high and low groundwater conditions;(D) Monitoring wells shall be sealed from the ground surface to the top of the filter pack;(E) Monitoring wells or devices intercept the excavation zone or are as close to it as is technically feasible;(F) The continuous monitoring devices or manual methods used can detect the presence of at least one-eighth of an inch of free product on top of the groundwater in the monitoring wells;(G) Within and immediately below the UST system excavation zone, the site is assessed to ensure compliance with the requirements in subparagraphs (A) to (E) and to establish the number and positioning of monitoring wells or devices that will detect releases from any portion of the tank that routinely contains product; and(H) Monitoring wells are clearly marked and secured to avoid unauthorized access and tampering. (7) Interstitial monitoring. Interstitial monitoring between the UST system and a secondary barrier immediately around or beneath it may be used, but only if the system is designed, constructed, and installed to detect a leak from any portion of the tank that routinely contains product and also meets one of the following requirements: (A) For double walled UST systems, the sampling or testing method can detect a leak through the inner wall in any portion of the tank that routinely contains product;(B) For UST systems with a secondary barrier within the excavation zone, the sampling or testing method used can detect a leak between the UST system and the secondary barrier; (i) The secondary barrier around or beneath the UST system consists of artificially constructed material that is sufficiently thick and impermeable (at least 10-6 cm/sec for the regulated substance stored) to direct a leak to the monitoring point and permit its detection;(ii) The barrier is compatible with the regulated substance stored so that a leak from the UST system will not cause a deterioration of the barrier allowing a release to pass through undetected;(iii) For cathodically protected tanks, the secondary barrier must be installed so that it does not interfere with the proper operation of the cathodic protection system;(iv) The groundwater, soil moisture, or rainfall will not render the testing or sampling method used inoperative so that a release could go undetected for more than thirty-one days;(v) The site is assessed to ensure that the secondary barrier is always above the groundwater and not in a twenty-five-year flood plain, unless the barrier and monitoring designs are for use under such conditions; and,(vi) Monitoring wells are clearly marked and secured to avoid unauthorized access and tampering.(C) For tanks with an internally fitted liner, an automated device can detect a leak between the inner wall of the tank and the liner, and the liner is compatible with the substance stored.(8) Statistical inventory reconciliation. Release detection methods based on the application of statistical principles to inventory data similar to those described in paragraph (1) must meet the following requirements: (A) Report a quantitative result with a calculated leak rate;(B) Be capable of detecting a leak rate of 0.2 gallon per hour or a release of one hundred fifty gallons within thirty-one days; and(C) Use a threshold that does not exceed one-half the minimum detectible leak rate.(9) Other methods. Any other type of release detection method, or combination of methods, can be used if: (A) It can detect a 0.2 gallon per hour leak rate or a release of one hundred fifty gallons within a month with a probability of detection of 0.95 and a probability of false alarm of 0.05; or(B) The owner and operator can demonstrate to the department that the method can detect a release as effectively as any of the methods allowed in paragraphs (3) to (8), and the department approves the method. In comparing methods, the department shall consider the size of release that the method can detect and the frequency and reliability with which it can be detected. If the method is approved, the owner and operator must comply with any conditions imposed by the department on its use to ensure the protection of human health and the environment.(10) Methods of release detection for field-constructed tanks. One or a combination of the following methods of release detection for tanks may be used when allowed by section 11-280.1-41. (A) Conduct an annual tank tightness test that can detect a 0.5 gallon per hour leak rate;(B) Use an automatic tank gauging system to perform release detection at least every thirty-one days that can detect a leak rate less than or equal to one gallon per hour. This method must be combined with a tank tightness test that can detect a 0.2 gallon per hour leak rate performed at least every three years;(C) Use an automatic tank gauging system to perform release detection at least every thirty-one days that can detect a leak rate less than or equal to two gallons per hour. This method must be combined with a tank tightness test that can detect a 0.2 gallon per hour leak rate performed at least every two years;(D) Perform vapor monitoring (conducted in accordance with paragraph (5) for a tracer compound placed in the tank system) capable of detecting a 0.1 gallon per hour leak rate at least every two years;(E) Perform inventory control (conducted in accordance with Department of Defense Directive 4140.25, ATA Airport Fuel Facility Operations and Maintenance Guidance Manual, or equivalent procedures) at least every thirty-one days that can detect a leak equal to or less than 0.5 percent of flow-through; and (i) Perform a tank tightness test that can detect a 0.5 gallon per hour leak rate at least every two years; or(ii) Perform vapor monitoring or groundwater monitoring (conducted in accordance with paragraph (5) or (6), respectively, for the stored regulated substance) at least every thirty-one days; or(F) Another method approved by the department if the owner and operator can demonstrate that the method can detect a release as effectively as any of the methods allowed in subparagraphs (A) to (E). In comparing methods, the department shall consider the size of release that the method can detect and the frequency and reliability of detection.Haw. Code R. § 11-280.1-43
[Eff 7/15/2018] (Auth: HRS §§ 342L-3, 342L-32, 342L-33) (Imp: HRS §§ 342L-3, 342L-32, 342L-33)