49 C.F.R. §§ 179.400-8

Current through November 30, 2024

Section 179.400-8 - Thickness of plates

(a) The minimum wall thickness, after forming, of the inner shell and any 2:1 ellipsoidal head for the inner tank must be that specified in § 179.401-1 , or that calculated by the following formula, whichever is greater:

t = Pd / 2SE

Where:

t = minimum thickness of plate, after forming, in inches;

P = minimum required bursting pressure in psig;

d = inside diameter, in inches;

S = minimum tensile strength of the plate material, as prescribed in AAR Specifications for Tank Cars, appendix M, Table M1 (IBR, see § 171.7 of this subchapter), in psi;

E = 0.9, a factor representing the efficiency of welded joints, except that for seamless heads, E = 1.0.

(b) The minimum wall thickness, after forming, of any 3:1 ellipsoidal head for the inner tank must be that specified in § 179.401-1 , or that calculated by the following formula, whichever is greater:

t = 1.83 Pd / 2SE

Where:

t = minimum thickness of plate, after forming, in inches;

P = minimum required bursting pressure in psig;

d = inside diameter, in inches;

S = minimum tensile strength of the plate material, as prescribed in AAR Specifications for Tank Cars, Appendix M, Table M1, in psi;

E = 0.9, a factor representing the efficiency of welded joints, except that for seamless heads, E = 1.0.

(c) The minimum wall thickness, after forming, of a flanged and dished head for the inner tank must be that specified in § 179.401-1 , or that calculated by the following formula, whichever is greater:

t = [PL(3 + [RADIC](L/r))] / (8SE)

Where:

t = minimum thickness of plate, after forming, in inches;

P = minimum required bursting pressure in psig;

L = main inside radius of dished head, in inches;

r = inside knuckle radius, in inches;

S = minimum tensile strength of plate material, as prescribed in AAR Specifications for Tank Cars, appendix M, table M1, in psi;

E = 0.9, a factor representing the efficiency of welded joints, except that for seamless heads, E = 1.0.

(d)

(1) The minimum wall thickness, after forming, of the outer jacket shell may not be less than ⁷/₁₆ inch. The minimum wall thickness, after forming, of the outer jacket heads may not be less than ¹/₂ inch and they must be made from steel specified in § 179.16(c) .

(2) For DOT 113C120W9 tank cars, the minimum wall thickness of the outer jacket shell and the outer jacket heads must be no less than ⁹/₁₆ inch after forming, and must be made of AAR TC-128, Grade B normalized steel plate.

(3) The annular space is to be evacuated, and the cylindrical portion of the outer jacket between heads, or between stiffening rings if used, must be designed to withstand an external pressure of 37.5 psig (critical collapsing pressure), as determined by the following formula:

P_c = [2.6E(t/D)^2.5]/[(L/D) - 0.45(t/D)^0.5]

Where:

P_c = Critical collapsing pressure (37.5 psig minimum) in psig;

E = modulus of elasticity of jacket material, in psi;

t = minimum thickness of jacket material, after forming, in inches;

D = outside diameter of jacket, in inches;

L = distance between stiffening ring centers in inches. (The heads may be considered as stiffening rings located ¹/₃ of the head depth from the head tangent line.)

49 C.F.R. §§179.400-8

Amdt. 179-32, 48 FR 27708, June 16, 1983; 49 FR 42736, Oct. 24, 1984; 64 FR 51920, Sept. 27, 1999, as amended at 66 FR 45390 , Aug. 28, 2001; 68 FR 75763 , Dec. 31, 2003; 85 FR 45030 , July 24, 2020

85 FR 45030 , 8/24/2020