Section 51-11R-40340 - Section R403.5-Service hot water systemsR403.5Service hot water systems. Energy conservation measures for service hot water systems shall be in accordance with this section. Service water-heating equipment shall meet the requirements of DOE 10 C.F.R. Part 430 Uniform Energy Factor or the equipment shall meet the requirements of Section C404.2. R403.5.1Heated water circulation and temperature maintenance systems.Heated water circulation systems shall be in accordance with Section R403.5.1.1. Heat trace temperature maintenance systems shall be in accordance with Section R403.5.1.2. Automatic controls, temperature sensors and pumps shall be in a location with access. Manual controls shall be in a location with ready access.
R403.5.1.1Circulation systems. Heated water circulation systems shall be provided with a circulation pump. The system return pipe shall be a dedicated return pipe. Gravity and thermosyphon circulation systems are prohibited. Controls automatically turn off the circulation pump when the water in the circulation loop is at the desired temperature and when there is no demand for hot water. R403.5.1.1.1Demand recirculation water systems serving an individual dwelling unit.Demand recirculation water systems shall have controls that start the pump upon receiving a signal from the action of a user of a fixture or appliance, sensing the presence of a user of a fixture or sensing the flow of hot or tempered water to a fixture fitting or appliance.R403.5.1.2Heat trace systems. Electric heat trace systems shall comply with IEEE 515.1 or UL 515. Controls for such systems shall automatically adjust the energy input to the heat tracing to maintain the desired water temperature in the piping in accordance with the times when heated water is used in the occupancy.R403.5.2Water volume determination. The volume shall be the sum of the internal volumes of pipe, fittings, valves, meters, and manifolds between the nearest source of heated water and the termination of the fixture supply pipe. Water heaters, circulating water systems, and heat trace temperature maintenance systems shall be considered to be sources of heated water. The volume in the piping shall be determined from Table C404.3.1 in the Washington State Energy Code, Commercial Provisions or Table L502.7 of the Uniform Plumbing Code. The volume contained within fixture shutoff valves, within flexible water supply connectors to a fixture fitting and within a fixture fitting shall not be included in the water volume determination. Where heated water is supplied by a recirculating system or heat-traced piping, the volume shall include the portion of the fitting on the branch pipe that supplies water to the fixture.R403.5.3Hot water pipe insulation. Insulation for service hot water pipe, both within and outside the conditioned space, shall have a minimum thermal resistance (R-value) of R-3. EXCEPTION: | Pipe insulation is permitted to be discontinuous where it passes through studs, joists or other structural members and where the insulated pipes pass other piping, conduit or vents, provided the insulation is installed tight to each obstruction. |
R403.5.4Drain water heat recovery units. Drain water heat recovery units shall comply with CSA 55.2 or IAPMO PS 92. Drain water heat recovery units shall be in accordance with CSA 55.1 or IAPMO IGC 346-2017.R403.5.5Water heater installation location. Service hot water systems shall be installed within the building thermal envelope. EXCEPTIONS: | 1. Where the hot water system efficiency is greater than or equal to 2.0 UEF. 2. Tankless water heaters. 3. Gas heat pump water heaters intended for exterior installation. 4. Atmospheric vented gas water heaters. |
R403.5.6Water heater insulation. All tank-type water heaters in unconditioned spaces, or on concrete floors in conditioned spaces, shall be placed on an insulated surface with a minimum thermal resistance of R-10, and a minimum compressive strength of 40 psi or engineered to support the appliance.R403.5.7Supplementary heat for heat pump water heating systems.Heat pumps used for water heating and having supplementary water heating equipment shall have controls that limit supplementary water heating equipment operation to only those times when one of the following applies:
1. The heat pump water heater cannot meet hot water demand.2. For heat pumps located in unconditioned space, the outside air temperature is below 40°F (4°C).3. The heat pump is operating in defrost mode.4. The vapor compression cycle malfunctions or loses power. EXCEPTION: | Heat trace temperature maintenance systems, provided the system capacity does not exceed the capacity of the heat pump water heating system. |
Wash. Admin. Code § 51-11R-40340
Amended by WSR 14-24-053, Filed 11/25/2014, effective 5/1/2015Amended by WSR 16-02-127, Filed 1/6/2016, effective 7/1/2016Amended by WSR 20-01-047, Filed 12/9/2019, effective 7/1/2020Amended by WSR 23-02-060, Filed 1/3/2023, effective 7/1/2023Amended by WSR 24-03-084, Filed 1/16/2024, effective 3/15/2024Statutory Authority: RCW 19.27A.025, 19.27A.045, and 19.27.074. WSR 13-20-121, § 51-11R-40340, filed 10/1/13, effective 11/1/13. Statutory Authority: RCW 19.27A.020, 19.27A.045 and chapters 19.27 and 34.05 RCW. WSR 13-04-055, § 51-11R-40340, filed 2/1/13, effective 7/1/13. WSR 13-20-001, § 51-11R-40340, filed 9/18/2013, effective 10/19/2013