Section 296-155-55600 - General requirements(1) You must use at least one qualified rigger as follows: (a) During hoisting activities for assembly and disassembly work (WAC 296-155-53402(19)(a) );(b) Whenever employees are engaged in hooking, unhooking, or guiding a load, or in the initial connection of a load to a component or structure, and are within the fall zone (WAC 296-155-53400(43)(c) ). | Note: | See qualified rigger requirements located in WAC 296-155-53306 of this part. |
(2) All slings in use must meet the applicable requirements for design, inspection, construction, testing, maintenance and operation as prescribed in ASME B30.9-2010.(3) All rigging hardware in use must meet the applicable requirements for design, inspection, construction, testing, maintenance and operation as prescribed in ASME B30.26-2010.(4) You must use all rigging gear in accordance with the manufacturer's recommendations or a qualified person.(5) All below-the-hook lifting devices in use must meet the applicable requirements for design, inspection, construction, testing, maintenance and operation as prescribed in ASME B30.20-2010.(6) All hooks in use must meet the applicable requirements for design, inspection, construction, testing, maintenance and operation as prescribed in ASME B30.10-2009.(7) Repair of hooks must be approved by the manufacturer or qualified person and as follows: (a) Cracks, nicks, and gouges may be repaired by a competent person, all other repairs are done by the manufacturer or a qualified person;(b) Grind longitudinally, following the contour of the hook;(c) Do not reduce the dimension of the hook more than 10% from the original.(8) You must not modify hooks by welding and/or drilling unless written approval by the manufacturer has been received.(9) You must mark special custom design grabs, hooks, clamps, or other lifting accessories, for such units as modular panels, prefabricated structures and similar materials, to indicate the safe working loads and they must be proof tested prior to use to 125% of their rated load.(10) A qualified person must inspect the rigging equipment before each day or shift and: (a) Consider the application the equipment will be used for, and determine if it's safe for use;(b) Remove the equipment from service if using it will create a hazard or meets any of the removal criteria listed in this chapter.(11) The rated load of the rigging equipment must not be exceeded.(12) All rigging hardware must have permanently affixed and legible identification markings as prescribed by the manufacturer that indicate the recommended safe working load.(13) You must inspect all rigging hardware in accordance with Table 11, each day before using. If a daily inspection is not feasible because the hardware is in a semipermanent or inaccessible location, a periodic inspection is allowed instead of daily.(14) You must remove rigging hardware from service when it shows any conditions listed in Table 11, or any other hazardous condition. Table 11
Rigging Hardware Inspection/Removal Criteria
| For all hardware, inspect for the following: |
| Missing or illegible identification. |
| Indications of heat damage, including weld spatter or arc strikes. |
| Excessive pitting or corrosion. |
Load bearing components that are: * Bent; * Twisted; * Distorted; * Stretched; * Elongated; * Cracked; * Broken. |
| Excessive nicks or gouges. |
| 10% reduction of the original or catalog dimension at any point. |
| Excessive thread damage or wear, where applicable. |
| Evidence of unauthorized welding or modification. |
| Any other conditions that cause doubt as to the safety of continued use. |
| On shackles, also inspect for incomplete pin engagement. |
| On swivels and swivel hoist rings, check for lack of ability to freely rotate or pivot. |
On compression hardware, also check for: Unauthorized replacement components; Insufficient number of wire rope clips; Improperly tightened wire rope clips; Damaged wire rope; |
Indications of wire rope slippage; Improper assembly. |
| On swivels, check for loose or missing nuts, bolts, cotter pins, snap rings, or other fasteners and retaining devices. |
On blocks check for: * Loose or missing nuts, bolts, cotter pins, snap rings, or other fasteners and retaining devices; * Misalignment or wobble in sheaves; * Excessive sheave groove corrugation or wear. |
(15) Any alteration or modification of rigging hardware must be in accordance with the hardware manufacturer or a qualified person and proof load tested to 125%. You must document this test and make it available upon request.(16) Welding of rigging hardware is prohibited unless authorized by the manufacturer or an RPE.(17) Replacement parts must meet or exceed the original rigging hardware manufacturer's specifications.(18) Rigging hardware selection must have the characteristics suitable for the application and environment where it will be used.(19) Workers must keep all parts of their body from between the load and any rigging during the lift.(20) If handling intermodal shipping containers at a construction site, you must follow the requirements in chapter 296-56 WAC, longshore, stevedore and waterfront related operations, Part F, Specialized terminals and the guidelines found in International Organization for Standardization (ISO) 3874 - Series 1 Freight Containers, fifth edition - Handling and Securing.Wash. Admin. Code § 296-155-55600
Amended by WSR 16-09-085, Filed 4/19/2016, effective 5/20/2016Statutory Authority: RCW 49.17.010, 49.17.040, 49.17.050, 49.17.060 and chapter 49.17 RCW, and 29 C.F.R. 1926, Subpart CC. 13-02-068, § 296-155-55600, filed 12/31/12, effective 2/1/13. Statutory Authority: RCW 49.17.010, 49.17.040, 49.17.050, 49.17.440, 49.17.060, and 29 C.F.R. 1926, Subpart CC. 12-01-086, § 296-155-55600, filed 12/20/11, effective 2/1/12.