9 Va. Admin. Code § 25-151-240
Current through Register Vol. 41, No. 9, December 16, 2024
Section 9VAC25-151-240 - Sector Q - Water transportation and ship and boat building and repairing yardsA. Discharges covered under this section. The requirements listed under this section apply to stormwater discharges associated with the following industrial activities: 1. Water transportation facilities identified by SIC Codes 4412-4499 (except SIC Code 4499 facilities as specified in Sector N - 9VAC25-151-210). The water transportation industry includes facilities engaged in foreign or domestic transport of freight or passengers in deep sea or inland waters, marine cargo handling operations, ferry operations, towing and tugboat services, and marinas.2. Ship building and repairing and boat building and repairing facilities identified by SIC Codes 3731 and 3732. The U.S. Coast Guard refers to a vessel 65 feet or greater in length as a "ship" and a vessel smaller than 65 feet as a "boat."B. Special conditions. Prohibition of nonstormwater discharges. In addition to the general nonstormwater prohibition in Part I B 1, the following discharges are not covered by this permit: bilge and ballast water, sanitary wastes, pressure washwater, and cooling water originating from vessels.C. Stormwater controls. 1. Good housekeeping. a. Pressure washing area. As defined by this permit, process wastewater related to hull work at facilities shall be any water used on a vessel's hull for any purpose, regardless of application pressure, including the activities of removing marine salts, sediments, marine growth and paint, or other hull, weather deck, or superstructure cleaning activities using water, (e.g., preparing those areas for inspection or work that may include cutting, welding, grinding, or coating). The discharge water shall be permitted as a process wastewater by a separate VPDES permit.b. Blasting and painting areas. The permittee shall describe and implement measures to prevent spent abrasives, paint chips, and overspray from discharging into the receiving water or the storm sewer system. The permittee shall contain all blasting or painting activities or use other measures to prevent or minimize the discharge of contaminants (e.g., hanging plastic barriers or tarpaulins during blasting or painting operations to contain debris). Stormwater conveyances shall be regularly cleaned to remove deposits of abrasive blasting debris and paint chips. The SWPPP shall include any standard operating practices with regard to blasting and painting activities, (e.g., the prohibition of uncontained blasting or painting over open water, or the prohibition of blasting or painting during windy conditions which can render containment ineffective).c. Material storage areas. All containerized materials shall be plainly labeled and stored in a protected, secure location away from drains. The permittee shall describe and implement measures to prevent or minimize the contamination of precipitation or surface runoff from the storage areas. The SWPPP shall specify which materials are stored indoors and consider containment or enclosure for materials that are stored outdoors. The permittee shall consider implementing an inventory control plan to limit the presence of potentially hazardous materials on-site. Where abrasive blasting is performed, the SWPPP shall specifically include a discussion on the storage and disposal of spent abrasive materials generated at the facility.d. Engine maintenance and repair areas. The permittee shall describe and implement measures to prevent or minimize contamination of precipitation or surface runoff from all areas used for engine maintenance and repair. The permittee shall consider the following measures (or their equivalent): performing all maintenance activities indoors, maintaining an organized inventory of materials used in the shop, draining all parts of fluids before disposal, prohibiting the practice of hosing down the shop floor using dry cleanup methods, and treating or recycling stormwater runoff collected from the maintenance area.e. Material handling areas. The permittee shall describe and implement measures to prevent or minimize contamination of precipitation or surface runoff from material handling operations and areas (e.g., fueling, paint and solvent mixing, disposal of process wastewater streams from vessels). The permittee shall consider the following measures or their equivalents: covering fueling areas; using spill and overflow protection; mixing paints and solvents in a designated area (preferably indoors or under a shed); and minimizing run-on of stormwater to material handling areas.f. Drydock activities. The SWPPP shall address the routine maintenance and cleaning of the drydock to minimize the potential for pollutants in the stormwater runoff. The SWPPP shall describe the procedures for cleaning the accessible areas of the drydock before flooding and final cleanup after the vessel is removed and the dock is raised. Cleanup procedures for oil, grease, or fuel spills occurring on the drydock shall also be included within the SWPPP. The permittee shall consider the following measures or their equivalents: sweeping rather than hosing off debris and spent blasting material from the accessible areas of the drydock before flooding; and having absorbent materials and oil containment booms readily available to contain or cleanup any spills.g. General yard area. The SWPPP shall include a schedule for routine yard maintenance and cleanup. Scrap metal, wood, plastic, miscellaneous trash, paper, glass, industrial scrap, insulation, welding rods, packaging, etc. shall be routinely removed from the general yard area.(1) Preventative maintenance. As part of the facility's preventive maintenance program, stormwater management devices shall be inspected and maintained in a timely manner (e.g., oil/water separators and sediment traps cleaned to ensure that spent abrasives, paint chips, and solids are intercepted and retained before entering the storm drainage system). Facility equipment and systems shall also be inspected and tested to uncover conditions that could cause breakdowns or failures resulting in discharges of pollutants to surface waters.(2) Routine facility inspections. The following areas shall be included in all quarterly inspections: pressure washing area; blasting, sanding, and painting areas; material storage areas; engine maintenance and repair areas; material handling areas; drydock area; and general yard area. The requirement for routine facility inspections is waived for facilities that have maintained an active VEEP E3/E4 status.(3) Employee training. Training shall address, at a minimum, the following activities (as applicable): used oil management, spent solvent management, disposal of spent abrasives, disposal of vessel wastewaters, spill prevention and control, fueling procedures, general good housekeeping practices, painting and blasting procedures, and used battery management.D. Benchmark monitoring and reporting requirements. These facilities are required to monitor their stormwater discharges for the pollutants of concern listed in Table 240. Table 240 Sector Q - Benchmark Monitoring Requirements |
Pollutants of Concern | Benchmark Concentration |
Water Transportation Facilities (SIC Codes 4412-4499 except 4499 as specified in Sector N) and Ship and Boat Building or Repairing Yards (SIC Codes 3731 and 3732) |
Total Suspended Solids (TSS) | 100 mg/L |
Total Recoverable Copper | 13 µg/L |
Total Recoverable Zinc | 120 µg/L |
9 Va. Admin. Code § 25-151-240
Derived from Virginia Register Volume 15, Issue 9, eff. June 30, 1999; amended, Virginia Register Volume 20, Issue 16, eff. July 1, 2004; Volume 25, Issue 19, eff. June 24, 2009; Amended, Virginia Register Volume 30, Issue 11, eff. July 1, 2014; Amended, Virginia Register Volume 35, Issue 19, eff. 7/1/2019; Amended, Virginia Register Volume 40, Issue 15, eff. 7/1/2024.Statutory Authority: § 62.1-44.15 of the Code of Virginia; § 402 of the Clean Water Act; 40 CFR Parts 122, 123, and 124.