N.J. Admin. Code § 7:26-6.3

Current through Register Vol. 56, No. 24, December 18, 2024

Section 7:26-6.3 - Types of wastes covered

(a) This subchapter applies to all solid waste, as defined at N.J.A.C. 7:26-2.13, with the exception of the following:

1. Bulk liquids and semi-liquids, ID type 72;

2. Septic tank clean-out wastes, ID type 73;

3. Liquid sewage sludge, ID type 74;

4. Dry sewage sludge, ID type 12;

5. Dry industrial waste, ID type 27, but only if such waste is residue from the operations of a scrap metal shredding facility, provided that the operator of the scrap metal shredding facility satisfies the requirements at (a)5i through iv below:

i. The owner/operator of the scrap metal shredding facility shall obtain the Department's approval of a quality control plan for the facility, which ensures that before shredding the motor vehicles, appliances, or source separated, non-putrescible ferrous and non-ferrous metals received by the facility, the facility removes components that could affect the nonhazardous characteristics of the residue from the operations of the facility. As provided in the quality control plan, the facility may reject any motor vehicles, appliances or source separated non-putrescible ferrous and non-ferrous metal if inspection reveals that components that could affect the non-hazardous characteristics of the residue are present. The facility is considered the generator of the components it accepts for processing, and shall dispose of these components in accordance with all applicable laws, orders and regulations (including N.J.A.C. 7:26G, if applicable). The components to be removed include, without limitation, the following:

(1) Batteries and cable ends;

(2) Gas tanks;

(3) Catalytic converters;

(4) Unspent airbag canisters;

(5) Transformers;

(6) PCB capacitors; and

(7) Fluorescent lighting fixtures;

ii. The owner/operator of the scrap metal processing facility shall obtain the Department's approval of a sampling and analytical plan which insures monitoring of the characteristics of the residue from the operations of the facility, as set forth at N.J.A.C. 7:26G-5 and the most recent edition of the USEPA publication SW-846 "Test Methods for Evaluating Solid Waste-Physical/Chemical Methods," incorporated herein by reference. The operator shall perform sampling and analysis quarterly, including, without limitation, the Toxicity Characteristic Leaching Procedure (TCLP) parameter as set forth at N.J.A.C. 7:26G-5. The operator shall submit the analysis performed in accordance with the approved sampling to the Division of Sustainable Waste Management for classification on January 15, April 15, July 15, and October 15, provided, however, that if the Department approves less frequent sampling and analysis, the owner/operator shall submit the analysis on the dates specified in the Department's approval of that sampling. Upon a request by the facility and as approved by the Department, the sampling frequency of the approved sampling and analytical plan may be reduced. The owner/operator of the facility shall submit a revised sampling and analytical plan which documents how the accuracy and precision criteria as required in SW-846 will be maintained with a reduced schedule;

iii. On February 15 and August 1 of every year, the owner/operator of the scrap metal shredding facility shall submit to the Department and to the solid waste district in which the facility is located, a report on forms provided by the Department consistent with the Department's Annual Recycling Tonnage Reporting Manual, including the following information:

(1) The total amount of each type of materials which the facility received in the six-month period ending January 1st and July 1st of every year;

(2) The total amount of residue disposed of by the facility;

(3) The total amount of ferrous and non-ferrous metal remaining after shredding; and

(4) The report shall be submitted to the following address:

New Jersey Department of Environmental Protection

Division of Sustainable Waste Management

Bureau of Solid Waste Planning and Licensing

Mail Code 401-02C

PO Box 420

401 East State Street

Trenton, NJ 08625-0420; and

iv. The scrap metal shredding facility shall either maintain a scale certified under N.J.A.C. 13:47B-1 and provide specific truck load weigh data to the district in which the facility is located, or transport the residue through the district's weighing facilities to be weighed before the residue is transported for disposal;

6. Source separated Class A recyclable material, Class B recyclable material, Class C recyclable material and Class D recyclable material as such terms are defined at N.J.A.C. 7:26A-1.3;

7. Hazardous waste, as defined at N.J.A.C. 7:26G-5; and

8. Non-residentially generated chemically treated wood, such as wood treated with creosote, pentachlorophenol (PCP), or chromated copper arsenate (CCA), or scrap tires that are destined for incineration and/or energy recovery provided that the following conditions are met:

i. The chemically treated wood or scrap tires are separated at the point of generation from other solid waste;

ii. The chemically treated wood or scrap tires transported for incineration and energy recovery are transported by a solid waste transporter licensed under N.J.A.C. 7:26-3, 16 and 16A. Transporters delivering chemically treated wood scrap or scrap tires to an out-of-State power generating incinerator pursuant to (a)8iv(1) below shall submit a tonnage report to the Department at the address specified at (a)8v below by March 1 of each year for the prior calendar year that specifies the total amount of material received, in tons, from New Jersey sources;

iii. Each load of chemically treated wood or scrap tires is accompanied by the waste origin/waste disposal form satisfying the requirements of N.J.A.C. 7:26-2.13(c); and

iv. The chemically treated wood or scrap tires are delivered to one or both of the following:

(1) An out-of-State power generating incinerator authorized or permitted by the receiving state to accept such materials for utilization as fuel; or

(2) An in-State power generating incinerator, including a resource recovery facility, that is approved by the Department to accept such materials for utilization as fuel subject to a review of the facility's operating permit, incoming materials specifications and written narrative explanation of operation. An in-state resource recovery facility that accepts chemically treated wood or scrap tires shall obtain an approved tariff for the receipt of these materials pursuant to N.J.A.C. 7:26H-5 and modify its solid waste facility permit pursuant to N.J.A.C. 7:26-2.6. Each approved in-state power generating facility, with the exception of an in-state resource recovery facility which must report such activity in its facility monthly volume report pursuant to N.J.A.C. 7:26-2.13, shall submit a tonnage report specifying the total amount of chemically treated wood or scrap tires received, in tons, from New Jersey sources, to the Department at the address specified at (a)8v below by March 1 of each year for the prior calendar year.

v. Applications for approval and annual tonnage reports shall be submitted to:

New Jersey Department of Environmental Protection

Division of Sustainable Waste Management

Bureau of Solid Waste Planning and Licensing

Mail Code 401-02C

PO Box 420

401 East State Street

Trenton, N.J. 08625-0420; and

N.J. Admin. Code § 7:26-6.3

Amended by 47 N.J.R. 991(a), effective 5/18/2015.

Administrative Change, 55 N.J.R. 1922(b), effective 7/31/2023