N.J. Admin. Code § 16:53A-3.2
Current through Register Vol. 56, No. 19, October 7, 2024
Section 16:53A-3.2 - Brake system(a) The number of defective brakes is equal to or greater than 20 percent of brakes on the vehicle or combination. Steering axle brakes are to be included in the 20 percent criterion. A defective brake includes any brake that meets one of the following criteria:1. Absence of effective braking action upon application of the service brakes, such as brake linings failing to move or contact breaking surface upon application. This is a category 2 violation. The penalty for this violation shall be $ 200.00 per wheel.2. Missing or broken mechanical components including: shoes, linings, pads, springs, anchor pins, spiders, cam rollers, pushrods, and air chamber mounting bolts. This is a category 2 violation. The penalty for this violation shall be $ 200.00 per wheel.3. Loose brake components including: air chambers, spiders, and cam shaft support brackets. This is a category 2 violation. The penalty for this violation shall be $ 200.00 per wheel.4. Audible air leak at brake chamber. (Example: ruptured diaphragm, loose chamber clamp.) This is a category 2 violation. The penalty for this violation shall be $ 100.00 per wheel.5. Brake adjustment limits. Bring reservoir pressure between 90 and 100 psi, turn engine off and then fully apply the brakes.i. One brake at 1/4 inch or more above the adjustment limit. (Example: Type 30 clamp type brake chamber pushrod measured at 2 1/4 inches would be one defective brake.) This is a category 2 violation. The penalty for this violation shall be $ 100.00 per brake.ii. Two brakes less than 1/4 inch beyond the adjustment limit also equal one defective brake. (Example: Type 30 clamp type brake chamber pushrods measure--two at 2 1/8 inches.) This example would equal one defective brake. This is a category 2 violation. The penalty for this violation shall be $ 100.00 per brake.iii. Any wedge brake where the combined brake lining movement of both top and bottom shoe exceeds 1/8 inch. This is a category 2 violation. The penalty for this violation shall be $ 100.00 per brake.6. Brake linings or pads, except on power unit steering axles. i. Cracked, loose, or missing lining. Any violation under (a)6i(1), (2), (3) or (4) below is a category 2 violation. The penalty for each violation shall be $ 300.00 per wheel. Missing lining, under (a)6i(5) below, is a category 1 violation. The penalty for this violation shall be $ 2,000 per wheel.(1) Lining cracks or voids of 1/16 inch in width observable on the edge of the lining.(2) Portions of a lining segment missing such that a fastening device (trivet or bolt) is exposed when viewing the lining from the edge.(3) Cracks that exceed 1 1/2 inches in length.(4) Loose fitting segments. (Approximately 1/16 inch or more movement.)(5) Complete lining segment missing.ii. The following chart shall be adhered to in determining brake adjustment limits, and is incorporated herein by reference. | COMMERCIAL VEHICLE SAFETY ALLIANCE |
| NORTH AMERICAN UNIFORM OUT-OF-SERVICE CRITERIA |
| BRAKE ADJUSTMENT REFERENCE CHART |
| Reference: Paragraph 1.a. of Part II of the Out-of-Service Criteria Brake |
| Adjustment: Shall not exceed those specifications contained hereunder |
| relating to "Brake Adjustment Limit." (Dimensions are in inches.) |
| CLAMP TYPE BRAKE CHAMBER DATA |
| Type | Outside Diameter | Brake Adjustment Limit |
| 6 | 4 1/2 | 1 1/4 |
| 9 | 5 1/4 | 1 3/8 |
| 12 | 5 11/16 | 1 3/8 |
| 16 | 6 3/8 | 1 3/4 |
| 20 | 6 25/32 | 1 3/4 |
| 24 | 7 7/32 | 1 3/4 |
| 30 | 8 3/32 | 2 |
| 36 | 9 | 2 1/4 |
| NOTE: A brake found at the adjustment limit is not a violation. |
| 'LONG STROKE' CLAMP TYPE BRAKE CHAMBER DATA |
| Type | Outside Diameter | Brake Adjustment Limit |
| 16 | 6 3/8 | 2.0 |
| 20 | 6 25/32 | 2.0 |
| 24 | 7 7/32 | 2.0 |
| 24* | 7 7/32 | 2.5 |
| 30 | 8 3/32 | 2.5 |
| *For 3 inch maximum stroke type 24 chambers |
| NOTE: A brake found at the adjustment limit is not a violation. |
| TIE ROD STYLE PISTON BRAKE CHAMBER DATA |
| Type | Outside Diameter | Brake Adjustment Limit |
| 30 | 6 1/2 (165 mm) | 2.5 (64 mm) |
| NOTE: A brake found at the adjustment limit is not a violation. |
| BOLT TYPE BRAKE CHAMBER DATA |
| Type | Outside Diameter | Brake Adjustment Limit |
| A | 6 15/16 | 1 3/8 |
| B | 9 3/16 | 1 3/4 |
| C | 8 1/16 | 1 3/4 |
| D | 5 1/4 | 1 1/4 |
| E | 6 3/16 | 1 3/8 |
| F | 11 | 2 1/4 |
| G | 9 7/8 | 2 |
| NOTE: A brake found at the adjustment limit is not a violation. |
| ROTOCHAMBER DATA |
| Type | Outside Diameter | Brake Adjustment Limit |
| 9 | 4 9/32 | 1 1/2 |
| 12 | 4 13/16 | 1 1/2 |
| 16 | 5 13/32 | 2 |
| 20 | 5 15/16 | 2 |
| 24 | 6 13/32 | 2 |
| 30 | 7 1/16 | 2 1/4 |
| 36 | 7 5/8 | 2 3/4 |
| 50 | 8 7/8 | 3 |
| NOTE: A brake found at the adjustment limit is not a violation. |
| DD-3 BRAKE CHAMBER DATA |
| Type | Outside Diameter | Brake Adjustment Limit |
| 30 | 8 1/8 | 2 1/4 |
| NOTE: This chamber has three air lines and is found on motor coaches. |
| NOTE: A brake found at the adjustment limit is not a violation. |
| WEDGE BRAKE DATA |
| The combined movement of both brake shoe lining scribe marks shall not |
| exceed 1/8 inch (3.18 mm). |
iii. Evidence of oil seepage into or out of the brake lining/drum interface area. This must include wet contamination of the lining edge accompanied by evidence that further contamination will occur--such as oil running from the drum or a bearing seal. Grease on the lining edge, back of shoe, or drum edge and oil stains with no evidence of fresh oil leakage are not conditions for out-of-service. This is a category 2 violation. The penalty for this violation shall be $ 300.00 per wheel.iv. Air brakes: Lining with a thickness less than 1/4 inch or to wear indicator, if lining is so marked, measured at the shoe center for drum brakes or less than 1/8 inch for disc brakes. This is a category 1 violation. The penalty for this violation shall be $ 500.00 per wheel.v. Hydraulic and electric brakes: Lining with a thickness 1/16 inch or less at the shoe center for disc or drum brakes. This is a category 1 violation. The penalty for this violation shall be $ 500.00 per wheel.7. Missing brake on any axle required to have brakes. This is a category 1 violation. The penalty for this violation shall be $ 5,000 per wheel.(b) In addition to being included in the 20 percent criterion, the following criteria pertaining to steering axle brakes place a vehicle in an out-of-service condition:1. Absence of effective braking action on any steering axle of any vehicle required to have steering axle brakes. This is a category 2 violation. The penalty for this violation shall be $ 400.00 per wheel.2. Mismatch across any power unit steering axle of:i. Air chamber sizes. This is a category 1 violation. The penalty for this violation shall be $ 1,000 per wheel.ii. Slack adjuster length. This is a category 1 violation. The penalty for this violation shall be $ 1,000 per wheel.3. Brake linings or pads on the steering axle of any power unit: i. Cracked, loose or missing lining. Any violation under (b)3i(1), (2), (3) or (4) below is a category 2 violation. The penalty for each violation shall be $ 500.00 per wheel. Missing lining, under (b)3i(5) below, is a category 1 violation. The penalty for this violation shall be $ 3,000 per wheel.(1) Lining cracks or voids 1/16 inch in width observable on the edge of the lining.(2) Portions of a lining segment missing such that a fastening device (rivet or bolt) is exposed when viewing the lining from the edge.(3) Cracks that exceed 1 1/2 inches in length.(4) Loose lining segments. (Approximately 1/16 inch or more movement.)(5) Complete lining segment missing.ii. Evidence of oil seepage into or out of the brake lining/drum interface area. This must include wet contamination of that lining edge accompanied by evidence further contamination will occur--such as oil running from the drum or bearing seal. Grease on the lining edge, back of shoe, or drum edge and oil stains with no evidence of fresh oil leakage are not conditions for out-of-service. This is a category 2 violation. The penalty for this violation shall be $ 400.00 per wheel.iii. Lining with a thickness less than 3/16 inch for a shoe with a continuous strip of lining or 1/4 inch for a shoe with two pads for drum brakes or to wear indicator if lining is so marked, or less than 1/8 inch for air disc brakes, and 1/16 inch or less for hydraulic disc, drum and electric brakes. This is a category 1 violation. The penalty for this violation shall be $ 500.00 per wheel.(c) The following is the violation, category and penalty pertaining to parking brakes: 1. Any non-manufactured holes or cracks in the spring brake housing section of a parking brake. This is a category 2 violation. The penalty for this violation shall be $ 100.00.(d) The following are the violations, categories and penalties pertaining to brake drums or rotors (discs):1. Drums with any external crack or cracks that open upon brake application. Do not confuse short hairline heat check cracks with flexural cracks. This is a category 2 violation. The penalty for this violation shall be $ 300.00 per wheel.2. Any portion of the drum or rotor (discs) missing or in danger of falling away. This is a category 2 violation. The penalty for this violation shall be $ 300.00 per wheel.3. Rotors with any crack or cracks. Do not confuse short hairline heat check cracks with fatigue cracks. This is a category 2 violation. The penalty for this violation shall be $ 300.00 per wheel.(e) The following are the violations, categories and penalties pertaining to brake hose: 1. Hose with any damage extending through the outer reinforcement ply. (Rubber impregnated fabric cover is not a reinforcement ply. Thermoplastic nylon may have braid reinforcement or color difference between cover and inner tube. Exposure of second color is out-of-service.) This is a category 1 violation. The penalty for this violation shall be $ 300.00 per hose.2. Bulge/swelling when air pressure is applied. This is a category 2 violation. The penalty for this violation shall be $ 100.00 per hose.3. Hose with audible leak at other than a proper connection. This is a category 2 violation. The penalty for this violation shall be $ 100.00 per hose.4. Two hoses improperly joined such as a splice made by sliding the hose ends over a piece of tubing and clamping the hose to the tube. This is a category 1 violation. The penalty for this violation shall be $ 5,000 per hose.5. Air hose cracked, broken or crimped in such a manner as to restrict air flow. This is a category 2 violation. The penalty for this violation shall be $ 100.00 per hose.(f) The following are the violations, categories and penalties pertaining to brake tubing: 1. Tubing with an audible leak at other than a proper connection. This is a category 2 violation. The penalty for this violation shall be $ 100.00.2. Tubing cracked, damaged by heat, broken or crimped. This is a category 2 violation. The penalty for this violation shall be $ 100.00.(g) The following is the violation, category and penalty pertaining to the low pressure warning device: 1. Low pressure warning device missing, inoperative, or does not operate at 55 psi and below, or 1/2 of the governor cutout pressure, whichever is less. If either an audible or visual warning device is working, vehicle should not be placed out-of-service. This is a category 2 violation. The penalty for this violation shall be $ 100.00.(h) The following is the violation, category and penalty pertaining to air loss rate: 1. If an air leak is discovered and the reservoir pressure is not maintained when the governor is cut-in, the reservoir pressure is between 80 and 90 psi, the engine is at idle, and the service brakes are fully applied. This is a category 2 violation. The penalty for this violation shall be $ 100.00.(i) The following are the violations, categories and penalties pertaining to the air reservoir security: 1. Reservoir separated from its original attachment points by metal fatigue, broken or missing bolt. This is a category 2 violation. The penalty for this violation shall be $ 500.00.2. Reservoir separated from its original attachment points and the strap securing is rotted out or is improperly secured with bailing wire, coat hanger wire or other like material. This is a category 1 violation. The penalty for this violation shall be $ 5,000.(j) The following are the violations, categories and penalties pertaining to the air compressor (normally to be inspected when readily visible or when conditions indicate compressor problems):1. Loose compressor mounting bolts. This is a category 2 violation. The penalty for this violation shall be $ 100.00.2. Cracked, broken or loose pulley. This is a category 2 violation. The penalty for this violation shall be $ 100.00.3. Cracked or broken mounting brackets, braces or adapters. This is a category 2 violation. The penalty for this violation shall be $ 100.00.(k) The following are the violations, categories and penalties pertaining to hydraulic brakes (including power assist over hydraulic and engine driven hydraulic booster): 1. No pedal reserve with engine running. This is a category 2 violation. The penalty for this violation shall be $ 300.00.2. Master cylinder less than 1/4 full. This is a category 2 violation. The penalty for this violation shall be $ 300.00.3. Power assist unit fails to operate. This is a category 2 violation. The penalty for this violation shall be $ 300.00.4. Seeping or swelling brake hose(s) under application of pressure. This is a category 2 violation. The penalty for this violation shall be $ 100.00.5. Hydraulic hose(s) abraded (chafed) through outer cover-to-fabric layer. This is a category 2 violation. The penalty for this violation shall be $ 300.00.6. Fluid lines or connections restricted, crimped, cracked or broken. This is a category 2 violation. The penalty for this violation shall be $ 100.00.7. Any visually observed leaking hydraulic fluid in the brake system upon full application. This is a category 2 violation. The penalty for this violation shall be $ 100.00.8. Hydraulic system: brake failure/low fluid warning light on and/or inoperative. This is a category 2 violation. The penalty for this violation shall be $ 300.00.(l) The following are the violations, categories and penalties pertaining to the vacuum system: 1. Insufficient vacuum reserve to permit one full brake application after engine is shut off. This is a category 2 violation. The penalty for this violation shall be $ 300.00.2. Vacuum hose(s) or line(s) restricted, abraded (chafed) through outer cover-to-cord ply, crimped, cracked, broken, or has collapse of vacuum hose(s) when vacuum is applied. This is a category 2 violation. The penalty for this violation shall be $ 100.00.N.J. Admin. Code § 16:53A-3.2
Amended by R.2004 d.331, effective 9/7/2004.
See: 36 N.J.R. 1672(a), 36 N.J.R. 4163(a).
In (d), added 3.
Amended by R.2010 d.046, effective 2/16/2010.
See: 41 N.J.R. 3036(a), 42 N.J.R. 594(a).
In the introductory paragraph of (a), deleted ", provided, however, on a three axle bus, one defective brake shall constitute a violation" following "combination".