Minn. R. agency 144, ch. 4761, LEAD STANDARDS; METHODS, pt. 4761.2645
Current through Register Vol. 49, No. 20, November 12, 2024
Part 4761.2645 - METHODS FOR REMOVING LARGE AREAS OF INTERIOR PAINTSubpart 1.Applicability.The methods in this part must be used when performing lead hazard reduction of interior painted surfaces greater than ten percent of the surface area when working on trim around doors, windows, or other small building components, or greater than two square feet per room when working on other surfaces.
Subp. 2.Access required.A person must allow the commissioner to have access to a work site, according to Minnesota Statutes, section 144.99, subdivision 2, while the person performs regulated lead work.
Subp. 3.Containment preparation.A. A containment must be prepared according to this subpart before lead hazard reduction begins.B. The heating, ventilating, and air conditioning systems to the containment must be restricted.C. All objects that are contaminated or suspected of being contaminated with lead-based paint chips or lead-contaminated dust must be:(1) vacuumed with a HEPA-filtered vacuum;(3) disposed of as lead-contaminated waste.D. All movable objects must be removed from the containment.E. The floor of the containment must be cleaned using a vacuum with a HEPA filter to remove all visible paint chips.Subp. 4.Installing containment barriers.A. Objects that cannot be removed from the containment must be covered and secured with at least one layer of one-mil plastic sheeting.B. At least one layer of six-mil plastic sheeting must be placed over the entire floor of the containment. Plastic sheeting must be sealed to the perimeter of the containment where the walls and floors meet to prevent lead contamination of the floor surface.C. Temporary barriers of no less than six-mil plastic sheeting may divide a room to restrict the size of the room.D. Any openings to the containment must be covered with at least one-mil plastic sheeting to prevent the escape of dust and debris unless the opening can be secured from inside the containment.E. All heating, ventilating, and air conditioning vents within the containment must be sealed with an airtight seal of at least one-mil plastic sheeting.F. If exterior windows, doors, or associated components are to be treated or replaced from the interior, two layers of plastic sheeting must be attached to the exterior wall to cover the window or door opening. If the window or door being treated has an intact and operational storm window or door that will not be disturbed during the window or door treatment, no exterior plastic is required.Subp. 5.Residents.A. Residents who are not personally performing lead hazard reduction must not be present in the residence while work is ongoing.B. Residents may return to the residence for overnight occupancy when lead hazard reduction ceases for the day and cleanup is completed in the containment.C. Returning residents must be provided with lead-safe passage to a bathroom, at least one living area, and an entry and egress route.D. Residents must be restricted from gaining access to the containment until all work is completed, the clearance inspection is conducted according to part 4761.2670, and clearance dust sample results meet the standards under part 4761.2510, subpart 2.Subp. 6.Warning signs.Warning signs as required in part 4761.2615, item F, must be placed at all entries to the residence and all entries to containments within the residence. Signs must remain posted overnight if work is to continue the following day.
Subp. 7.Decontamination procedures.A. The certified lead firm, lead supervisor, or property owner performing the lead hazard reduction must provide proper washing facilities for workers to thoroughly wash hands, face, and other exposed body surfaces.B. If existing facilities are used at the work site to decontaminate, the certified lead firm, lead supervisor, or property owner must:(1) provide workers with soap and disposable towels; and(2) clean the existing facility until no visible dust, dirt, or debris remains each day before leaving the site.Subp. 8.Daily cleaning procedures.A. This subpart applies if work is to resume the next day.B. If plastic floor sheeting is left in place for the next day, it must be cleaned of visible dust and debris using a vacuum with a HEPA filter or using any other EPA-documented methodology under part 4761.2000, subpart 15, item K. Holes in the plastic must be sealed.C. If plastic floor sheeting is removed, it must be removed in a way to contain all lead-contaminated dust and debris and discarded as lead-contaminated. The exposed floor surface must be cleaned using a vacuum with a HEPA filter or using any other EPA-documented methodology under part 4761.2000, subpart 15, item K.D. All floors in adjacent areas, areas used as pathways to the containment, and any areas used to store equipment and waste materials must be cleaned using a vacuum with a HEPA filter and wet wiped or cleaned using any other EPA-documented methodology under part 4761.2000, subpart 15, item K.Subp. 9.Final cleaning procedures and inspection.A. When lead hazard reduction is completed, the certified lead firm, lead supervisor, or property owner must: (1) inspect all work surfaces where lead hazard reduction was conducted and visually determine that no dust, debris, or deteriorated paint remains;(2) remove all plastic sheeting from the floor and window and door openings and dispose of plastic sheeting as lead-contaminated waste;(3) clean all surfaces in the containment using a vacuum with a HEPA filter and wet wipe and clean a second time using a vacuum with a HEPA filter or clean using any other EPA-documented methodology under part 4761.2000, subpart 15, item K;(4) clean all floors in adjacent areas used as pathways to the containment and any areas used to store equipment and waste materials. Cleaning must be conducted using a vacuum with a HEPA filter and wet wipe or using any other EPA-documented methodology under part 4761.2000, subpart 15, item K;(5) if windows or doors were treated or replaced and the plastic sheeting on the exterior was breached, wet wipe that side of the window or door or clean using any other EPA-documented methodology under part 4761.2000, subpart 15, item K;(6) reinspect all areas referenced in subitems (1) to (5). If visible dust or debris is observed, the cleaning procedures under subitems (3) to (5) must be repeated until no visible dust or debris remains;(7) if paint was removed from building components, paint or seal the surfaces;(8) remove all remaining plastic sheeting and dispose of it as lead-contaminated waste and inspect the areas and items for dust and debris. If dust or debris is observed, surfaces must be cleaned using a vacuum with a HEPA filter; and(9) conduct clearance inspections according to part 4761.2670.B. A wet/dry vacuum may be used instead of a vacuum with a HEPA filter under this subpart, but must be used only to collect wash and rinse water from hard-surface floors. A wet/dry vacuum may not be used to vacuum a dry floor surface, ground surface, or carpeting.Minn. R. agency 144, ch. 4761, LEAD STANDARDS; METHODS, pt. 4761.2645
Statutory Authority: MS s 144.9508