Ill. Admin. Code tit. 32, pt. 315, tbl. A

Current through Register Vol. 48, No. 43, October 25, 2024

Table A - MPE for Ocular Exposure (Intrabeam Viewing)

Ultraviolet

Wavelength (µ m)	Exposure Duration, ts	(J cm-2)	MPE (W cm-2)
0.180 to 0.302	10-9 to 3 x 104	3 x 10-3
0.303	10-9 to 3 x 104	4 x 10-3
0.304	10-9 to 3 x 104	6 x 10-3
0.305	10-9 to 3 x 104	10 x 10-3
0.306	10-9 to 3 x 104	16 x 10-3
0.307	10-9 to 3 x 104	25 x 10-3
0.308	10-9 to 3 x 104	40 x 10-3
0.309	10-9 to 3 x 104	63 x 10-3
0.310	10-9 to 3 x 104	0.1
0.311	10-9 to 3 x 104	0.16
0.312	10-9 to 3 x 104	0.25
0.313	10-9 to 3 x 104	0.40
0.314	10-9 to 3 x 104	0.63
0.315 to 0.400	10-9 to 10	0.56 t1/4
0.315 to 0.400	10 x 3 x 104	1.0

NOTE: To calculate MPE, use the J cm^-2 value shown or 0.56t^1/4, whichever is lower.

Visible and Near Infrared

Wavelength (µ m)	Exposure Duration, ts	(J cm-2)	MPE (W cm-2)
0.400 to 0.700	10-9 to 18 x 10-6	0.5 x 10-6
0.400 to 0.700	18 x 10-6 to 10	1.8 t3/4 x 10-3
0.400 to 0.550	10 to 104	10 x 10-3
0.550 to 0.700	10 to T1	1.8 t3/4 x 10-3
0.550 to 0.700	T1 to 104	10CB to 10-3
0.400 to 0.700	104 to 3 x 104	CB x 10-6
0.700 to 1.050	10-9 to 18 x 10-6	0.5CA x 10-6
0.700 to 1.050	18 x 10-6 to 103	1.8CAt3/4 x 10-3
0.700 to 1.050	103 to 3 x 104	320CA x 10-6
1.050 to 1.400	10-9 to 50 x 10-6	5Cc x 10-6
1.050 to 1.400	50 x 10-6 to 103	9.0 Cct3/4 x 10-3
1.050 to 1.400	103 to 3 x 104	1.6 Cc x 10-3

NOTES:	1.	See Section 315.Tables D & E for limiting apertures (see ANSI Z136.1 pg. 44).
	2.	For multiple pulses, apply correction factor Cp given in Section 315.Table C.
	3.	For information on correction factors T1, CB, CA, Cp and Cc, see Section 315.Table C.

Far Infrared

Wavelength (µ m)	Exposure Duration, ts	(J cm-2)	MPE (W cm-2)
1.400 to 1.500	10-9 to 10-3	0.1
1.400 to 1.500	10-3 to 10	0.56t1/4
1.400 to 1.500	10 to 3 x 104	0.1
1.500 to 1.800	10-9 to 10	1.0
1.500 to 1.800	10 to 3 x 104	0.1
1.800 to 2.600	10-9 to 10-3	0.1
1.800 to 2.600	10-3 to 10	0.56t1/4
1.800 to 2.600	10 to 3 x 104	0.1
2.600 to 103	10-9 to 10-7	10 x 10-3
2.600 to 103	10-7 to 10	0.56t1/4
2.600 to 103	10 to 3 x 104	0.1

NOTES:	1.	See Section 315.Tables D & E for limiting apertures (see ANSI Z136.1 pg. 44).
2.	For multiple pulses, apply correction factor Cp given in Section 315.Table C.

GENERAL NOTES:	1.	The MPE for diffuse reflections at wave lengths between 0.400 and 1.400µm is obtained by multiplying the corresponding MPEs above by CE (see Section 315.Table C for correction factors and T1).
2.	For repeated (pulsed) exposures, see ANSI Z136.1.
3.	For purposes of this Section 315.Table A, the following abbreviations or symbols are used:
			µm	=	micrometers
			ts	=	time in seconds
			J	=	joules
			W	=	watts
			cm	=	centimeters

Ill. Admin. Code tit. 32, pt. 315, tbl. A