Section 622.189 - Restrictions and requirements for sea bass pots(a)Tending restriction. A sea bass pot in the South Atlantic EEZ may be pulled or tended only by a person (other than an authorized officer) aboard the vessel permitted to fish such pot or aboard another vessel if such vessel has on board written consent of the owner or operator of the vessel so permitted.(b)Configuration restriction. In the South Atlantic EEZ, sea bass pots may not be used or possessed in multiple configurations, that is, two or more pots may not be attached one to another so that their overall dimensions exceed those allowed for an individual sea bass pot. This does not preclude connecting individual pots to a line, such as a "trawl" or trot line.(c)Requirement for escape mechanisms.(1) A sea bass pot that is used or possessed in the South Atlantic EEZ between 35°15.19' N. lat. (due east of Cape Hatteras Light, NC) and 28°35.1' N. lat. (due east of the NASA Vehicle Assembly Building, Cape Canaveral, FL) is required to have- (i) On at least one side, excluding top and bottom, a panel or door with an opening equal to or larger than the interior end of the trap's throat (funnel). The hinges and fasteners of each panel or door must be made of one of the following degradable materials: (A) Ungalvanized or uncoated iron wire with a diameter not exceeding 0.041 inches (1.0 mm), that is, 19 gauge wire.(B) Galvanic timed-release mechanisms with a letter grade designation (degradability index) no higher than J.(ii) An unobstructed escape vent opening on at least two opposite vertical sides, excluding top and bottom. The minimum dimensions of an escape vent opening (based on inside measurement) are:(A) 11/8 by 53/4 inches (2.9 by 14.6 cm) for a rectangular vent.(B) 1.75 by 1.75 inches (4.5 by 4.5 cm) for a square vent.(C) 2.0-inch (5.1-cm) diameter for a round vent.(d)Construction requirements and mesh sizes.(1) A sea bass pot used or possessed in the South Atlantic EEZ must have mesh sizes as follows (based on centerline measurements between opposite, parallel wires or netting strands): (i) For sides of the pot other than the back panel:(A) Hexagonal mesh (chicken wire)-at least 1.5 inches (3.8 cm) between the wrapped sides;(B) Square mesh-at least 1.5 inches (3.8 cm) between sides; or(C) Rectangular mesh-at least 1 inch (2.5 cm) between the longer sides and 2 inches (5.1 cm) between the shorter sides.(ii) For the entire back panel, i.e., the side of the pot opposite the side that contains the pot entrance, mesh that is at least 2 inches (5.1 cm) between sides.(e)Requirements for pot removal.(1) A sea bass pot must be removed from the water in the South Atlantic EEZ and the vessel must be returned to a dock, berth, beach, seawall, or ramp at the conclusion of each trip. Sea bass pots may remain on the vessel at the conclusion of each trip.(2) A sea bass pot must be removed from the water in the South Atlantic EEZ when the applicable quota specified in § 622.190(a)(5) is reached. After a closure is in effect, a black sea bass may not be retained by a vessel that has a sea bass pot on board.(f)Restriction on number of pots. A vessel that has on board a valid Federal commercial permit for South Atlantic snapper-grouper and a South Atlantic black sea bass pot endorsement that fishes in the South Atlantic EEZ on a trip with black sea bass pots, may possess only 35 black sea bass pots per vessel per permit year. Each black sea bass pot in the water or onboard a vessel in the South Atlantic EEZ, must have a valid identification tag attached. Endorsement holders must apply for new tags each permit year through NMFS to replace tags from the previous year.(g)Sea bass pot buoy line marking requirement. In addition to the gear marking requirements specified in 50 CFR 229.32(b) , from November 15 through April 15, each year, in the Southeast U.S. Restricted Area North as described in 50 CFR 229.32(f) and from September 1 through May 31, each year in the Offshore Trap/Pot Waters Area and the Southern Nearshore Trap/Pot Waters Area, as described in 50 CFR 229.32(c)(6) and (9) , respectively, the buoy line must be marked with a purple color band. The colored band must be clearly visible when the gear is hauled or removed from the water, including if the color of the rope is the same as, or similar, to the colored band. The purple band must be marked directly onto the line and adjacent to the buoy line markings specified in 50 CFR 229.32(b) , that is, at the top, middle, and bottom of each buoy line deployed by, or on board, the vessel. Each of the three purple bands must be a 12-inch (30.5 cm) color mark. In marking or affixing the purple band, the line may be dyed, painted, or marked with thin colored whipping line, thin colored plastic, or heat-shrink tubing, or other material.81 FR 1792, Jan. 13, 2016, as amended at 81 FR 95902, Dec. 29, 2016 81 FR 1792, 1/13/2016, as amended at 81 FR 95902, 12/29/2016; 81 FR 95902, 1/30/2017; 82 FR 8820, 1/31/2017