Section 595.7 - Requirements for vehicle modifications to accommodate people with disabilities(a) Any motor vehicle repair business that modifies a motor vehicle to enable a person with a disability to operate, or ride as a passenger in, the motor vehicle is exempted from the "make inoperative" prohibition of 49 U.S.C. 30122 to the extent that those modifications affect the motor vehicle's compliance with the Federal motor vehicle safety standards or portions thereof specified in paragraph (c) of this section. Modifications that would take a vehicle out of compliance with any other Federal motor vehicle safety standards, or portions thereof, are not covered by this exemption.(b) Any motor vehicle repair business that modifies a motor vehicle to enable a person with a disability to operate, or ride as a passenger in, the motor vehicle in such a manner as to make inoperative any part of a device or element of design installed on or in the motor vehicle in compliance with a Federal motor vehicle safety standard or portion thereof specified in paragraph (c) of this section must affix to the motor vehicle a permanent label of the type and in the manner described in paragraph (d) of this section and must provide and retain a document of the type and in the manner described in paragraph (e) of this section.(c)(1)49 CFR 571.101 , except for S5.2.1, S5.3.1, S5.3.4, S5.4.1, and S5.4.3 of that section.(2) S9.1.1 of 49 CFR 571.108 , in the case of a motor vehicle that is modified to be driven without a steering wheel or for which it is not feasible to retain the turn signal canceling device installed by the vehicle manufacturer.(3) S5.1.2 and S5.1.3 of 49 CFR 571.114 , in any case in which the original key locking system must be modified.(4) S4(a) of 49 CFR 571.118 , in any case in which the medical condition of the person for whom the vehicle is modified necessitates the installation of a remote ignition switch to start the vehicle.(5) S5.1 and S5.2.1 of 49 CFR 571.123 , in any case in which the modification necessitates the relocation of original equipment manufacturer's controls.(6) S5.3.1 of 49 CFR 571.135 , in any case in which the modification necessitates the removal of the original equipment manufacturer foot pedal.(7)49 CFR 571.201 with respect to: (i) Targets located on the right side rail, the right B-pillar and the first right side "other" pillar adjacent to the stowed platform of a lift or ramp that stows vertically, inside the vehicle.(ii) Targets located on the left side rail, the left B-pillar and the first left side "other" pillar adjacent to the stowed platform of a lift or ramp that stows vertically, inside the vehicle.(iii) Targets located on the rear header and the rearmost pillars adjacent to the stowed platform of a lift or ramp that stows vertically, inside the vehicle.(iv) Targets located on any hand grip or vertical stanchion bar.(v) All of S6 of 571.201 in any case in which the disability necessitates raising the roof or door, or lowering the floor of the vehicle.(8)49 CFR 571.202 and 571.202a , in any case in which: (i) A motor vehicle is modified to be operated by a driver seated in a wheelchair and no other seat is supplied with the vehicle for the driver;(ii) A motor vehicle is modified to transport a right front passenger seated in a wheelchair and no other right front passenger seat is supplied with the vehicle; or(9)(i) For vehicles manufactured before March 14, 2005, S4.3(b)(1) and (2) of 49 CFR 571.202 , in any case in which the driver's head restraint must be modified to accommodate a driver with a disability.(ii) For vehicles manufactured on or after March 14, 2005 and certified to FMVSS No. 202, S4.2(b)(1) and (2) of 49 CFR 571.202 , in any case in which the head restraint must be modified to accommodate a driver with a disability.(iii) For vehicles manufactured on or after March 14, 2005 and certified to FMVSS No. 202a, S4.2.1(b) of 49 CFR 571.202a , in any case in which the head restraint must be modified to accommodate a driver or a front outboard passenger with a disability.(iv) For vehicles manufactured on or after March 14, 2005 and certified to FMVSS No. 202a, S4.2.2 of 49 CFR 571.202a , in any case in which the head restraint must be modified to accommodate a driver with a disability.(v) For vehicles manufactured before March 14, 2005 and certified to FMVSS No. 202, S4.3 of 49 CFR 571.202 , in any case in which the head restraint of the front passenger seat of a vehicle must be modified or replaced by a device to support or position the passenger's head or neck due to a disability.(vi) For vehicles manufactured on or after March 14, 2005 and certified to FMVSS No. 202, S4.2 of 49 CFR 571.202 , in any case in which the head restraint of the front passenger seat of a vehicle must be modified or replaced by a device to support or position the passenger's head or neck due to a disability.(vii) For vehicles manufactured on or after March 14, 2005 and certified to FMVSS No. 202a, S4.2.1, S4.2.2, S4.2.3, S4.2.4, S4.2.5, S4.2.6, and S4.2.7 of 49 CFR 571.202a , in any case in which the head restraint of the front passenger seat of a vehicle must be modified or replaced by a device to support or position the passenger's head or neck due to a disability.(10) S5.1 of 49 CFR 571.203 , in any case in which the modification necessitates a structural change to, or removal of, the original equipment manufacturer steering shaft.(11) S5.2 of 49 CFR 571.203 , in any case in which an item of adaptive equipment must be mounted on the steering wheel.(12)49 CFR 571.204 , in any case in which the modification necessitates a structural change to, or removal of, the original equipment manufacturer steering shaft.(13) S4.1 of 49 CFR 571.207 , in any case in which a vehicle is modified to be driven by a person seated in a wheelchair and no other driver's seat is supplied with the vehicle, provided that a wheelchair securement device is installed at the driver's position.(14) S4.1.5.1(a)(1), S4.1.5.1(a)(3), S4.2.6.2, S5, S7.1, S7.2, S7.4, S14, S15, S16, S17, S18, S19, S20, S21, S22, S23, S24, S25, S26 and S27 of 49 CFR 571.208 for the designated seating position modified, provided Type 2 or Type 2A seat belts meeting the requirements of 49 CFR 571.209 and 571.210 are installed at that position.(15) S7 and S9 of 49 CFR 571.214 , for the designated seating position modified, in any cases in which the restraint system and/or seat at that position must be changed to accommodate a person with a disability.(16)49 CFR 571.225 in any case in which an existing child restraint anchorage system, or built-in child restraint system relied upon for compliance with 571.225 must be removed to accommodate a person with a disability, provided the vehicle contains at least one tether anchorage which complies with 49 CFR 571.225 S6, S7 and S8 in one of the rear passenger designated seating positions. If no rear designated seating position exists after the vehicle modification, a tether anchorage complying with the requirements described above must be located at a front passenger seat. Any tether anchorage attached to a seat that is relocated shall continue to comply with the requirements of 49 CFR 571.225 S6, S7 and S8.(17) S4.2 and S5 of 49 CFR 571.226 , on the side of the vehicle where a seat on that side of the vehicle must be changed to accommodate a person with a disability.(18)49 CFR 571.216a , in any case in which: (i) The disability necessitates raising the roof; and,(ii) The vehicle, after modification, meets 49 CFR 571.220 .(19) S5.5.1, S5.5.2, S6.2.1, and S6.2.2 of 49 CFR 571.111 , in any case in which a personal mobility device transporter is temporarily installed on a vehicle by way of a trailer hitch to carry a personal mobility device (e.g., a wheelchair, powered wheelchair, or powered scooter) used by a driver or a passenger with a disability.(d) The label required by paragraph (b) of this section shall: (1) Be permanently affixed to the vehicle,(2) Be located adjacent to the original certification label or the alterer's certification label, if applicable,(3) Give the modifier's name and physical address,(4) Contain the statement "This vehicle has been modified in accordance with 49 CFR 595.6 and may no longer comply with all Federal Motor Vehicle Safety Standards in effect at the time of its original manufacture."(e) The document required by paragraph (b) of this section shall: (1) Be provided, in original or photocopied form, to the owner of the vehicle at the time the vehicle is delivered to the owner,(2) Be kept, in original or photocopied form, at the same address provided on the label described in paragraph (c) of this section for a period not less than five years after the vehicle, as modified, is delivered to the individual for whom the modifications were performed,(3) Be clearly identifiable as to the vehicle that has been modified,(4) Contain a list of the Federal motor vehicle safety standards or portions thereof specified in paragraph (c) of this section with which the vehicle may no longer be in compliance.(5) Indicate any reduction in the load carrying capacity of the vehicle of more than 100 kg (220 lb) after the modifications are completed. In providing this information, the modifier must state whether the weight of a user's wheelchair is included in the available load capacity. 66 FR 12655 , Feb. 27, 2001, as amended at 69 FR 21069 , Apr. 20, 2004; 70 FR 51678 , Aug. 31, 2005; 75 FR 47489 , Aug. 6, 2010; 76 FR 37028 , June 24, 2011; 76 FR 47083 , Aug. 4, 2011; 79 FR 38795 , July 9, 2014; 87 FR 14418 , Mar. 15, 2022