Statutes, codes, and regulations
Code of Federal Regulations
Title 49 - TransportationSubtitle B - OTHER REGULATIONS RELATING TO TRANSPORTATIONChapter I - PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATIONSubchapter C - HAZARDOUS MATERIALS REGULATIONSPart 179 - SPECIFICATIONS FOR TANK CARS
Subpart D - SPECIFICATIONS FOR NON-PRESSURE TANK CAR TANKS (CLASSES DOT-111AW, 115AW, AND 117AW)
Section 179.200-7 - Materials

49 C.F.R. § 179.200-7

Download
PDF
Current through May 31, 2024
Section 179.200-7 - Materials
(a) Plate material used to fabricate the tank and, when used, expansion dome or manway nozzle material, must meet one of the following specifications with the indicated minimum tensile strength and elongation in the welded condition.
(b)Carbon steel plate: The maximum allowable carbon content must be 0.31 percent when the individual specification allows carbon content greater than this amount. The plates may be clad with other approved materials:

SpecificationsMinimum tensile strength (p.s.i.) welded condition1Minimum elongation in 2 inches (percent) weld metal (longitudinal)
AAR TC 128, Gr. B81,00019
ASTM A 516270,00020

1Minimum stresses to be used in calculations.

2This specification is incorporated by reference (IBR, see §171.7 of this subchapter).

(c)Aluminum alloy plate: Aluminum alloy plate must be suitable for welding and comply with one of the following specifications (IBR, see §171.7 of this subchapter):

SpecificationsMinimum tensile strength (p.s.i.) welded condition3,4Minimum elongation in 2 inches (percent) 0 temper weld metal (longitudinal)
ASTM B 209, Alloy 5052125,00018
ASTM B 209, Alloy 5083238,00016
ASTM B 209, Alloy 5086135,00014
ASTM B 209, Alloy 5154130,00018
ASTM B 209, Alloy 5254130,00018
ASTM B 209, Alloy 5454131,00018
ASTM B 209, Alloy 5652125,00018

1For fabrication, the parent plate material may be 0, H112, or H32 temper, but design calculations must be based on minimum tensile strength shown.

20 temper only.

3Weld filler metal 5556 must not be used.

4Maximum stresses to be used in calculations.

(d)High alloy steel plate: High alloy steel plate must comply with one of the following specifications:

SpecificationsMinimum tensile strength (p.s.i.) welded condition1Minimum elongation in 2 inches (percent) weld metal (longitudinal)
ASTM A 240/A 240M (incorporated by reference; see§171.7 of this subchapter), Type 30475,00030
ASTM A 240/A 240M (incorporated by reference; see§171.7 of this subchapter), Type 304L70,00030
ASTM A 240/A 240M (incorporated by reference; see§171.7 of this subchapter), Type 31675,00030
ASTM A 240/A 240M (incorporated by reference; see§171.7 of this subchapter), Type 316L70,00030

1Maximum stresses to be used in calculations.

2High alloy steel materials used to fabricate tank and expansion dome, when used, must be tested in accordance with Practice A of ASTM Specification A 262 titled, "Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels" (IBR; see §171.7 of this subchapter). If the specimen does not pass Practice A, Practice B or C must be used and the corrosion rates may not exceed the following:

Test procedureMaterialCorrosion rate i.p.m.
Practice BTypes 304, 304L, 316, and 316L0.0040
Practice CType 304L.0020

Type 304L and Type 316L test specimens must be given a sensitizing treatment prior to testing. (A typical sensitizing treatment is 1 hour at 1250 F.)

(e)Nickel plate: Nickel plate must comply with the following specification (IBR, see §171.7 of this subchapter):

SpecificationsMinimum tensile strength (psi) welded condition1Minimum elongation in 2 inches (percent) weld metal (longitudinal)
ASTM B 162240,00020

(f)Manganese-molybdenum steel plate: Manganese-molybdenum steel plate must be suitable for fusion welding and comply with the following specification (IBR, see §171.7 of this subchapter):

SpecificationsMinimum tensile strength (p.s.i.) welded condition1Minimum elongation in 2 inches (percent) weld metal (longitudinal)
ASTM A 302, Gr. B80,00020

1Maximum stresses to be used in calculations.

(g) All parts and items of construction in contact with the lading must be made of material compatible with plate material and not subject to rapid deterioration by the lading, or be coated or lined with suitable corrosion resistant material.
(h) All external projections that may be in contact with the lading and all castings, forgings, or fabrications used for fittings or attachments to tank and expansion dome, when used, in contact with lading must be made of material to an approved specification. See AAR Specifications for Tank Cars, appendix M, M4.05 (IBR, see §171.7 of this subchapter) for approved material specifications for castings for fittings.

49 C.F.R. §179.200-7

Amdt. 179-10, 36 FR 21349, 11/9/1971; 36 FR 21893, 11/17/1971, as amended by Amdt.179-28, 46 FR 49906, 10/8/1981; Amdt. 179-40, 52 FR 13046, 4/20/1987; Amdt. 179-52, 61 FR 28680, 6/5/1996; 66 FR 45186, 8/28/2001; 67 FR 51660, 8/8/2002; 68 FR 75761, 12/31/2003; 70 FR 34076, 6/13/2005