Section 178.910 - Marking of Large Packagings(a) The manufacturer must:(1) Mark every Large Packaging in a durable and clearly visible manner. The marking may be applied in a single line or in multiple lines provided the correct sequence is followed with the information required by this section, in letters, numerals, and symbols of at least 12 mm in height. This minimum marking size requirement applies only to large packages manufactured after January 1, 2014. The following information is required in the sequence presented: (i) Except as provided in § 178.503(e)(1)(ii) , the United Nations packaging symbol as illustrated in § 178.503(e)(1)(i) . For metal Large Packagings on which the marking is stamped or embossed, the capital letters "UN" may be applied instead of the symbol;(ii)The code number designating the Large Packaging design type according to § 178.905 . The letters "T" or "W" may follow the Large Packaging design type identification code on a Large Packaging. Large Salvage Packagings conforming to the requirements of subpart P of this part must be marked with the letter "T". Large Packagings must be marked with the letter "W" when the Large Packaging differs from the requirements in subpart P of this part, or is tested using methods other than those specified in this subpart, and is approved by the Associate Administrator in accordance with the provisions in § 178.955 ;(iii) A capital letter identifying the performance standard under which the design type has been successfully tested, as follows:(A) X-for Large Packagings meeting Packing Groups I, II and III tests;(B) Y-for Large Packagings meeting Packing Groups II and III tests; and(C) Z-for Large Packagings meeting Packing Group III test.(iv) The month (designated numerically) and year (last two digits) of manufacture;(v) The country authorizing the allocation of the mark. The letters "USA" indicate that the Large Packaging is manufactured and marked in the United States in compliance with the provisions of this subchapter.(vi) The name and address or symbol of the manufacturer or the approval agency certifying compliance with subpart P and subpart Q of this part. Symbols, if used, must be registered with the Associate Administrator.(vii) The stacking test load in kilograms (kg). For Large Packagings not designed for stacking the figure "0" must be shown.(viii) The maximum permissible gross mass or for flexible Large Packagings, the maximum net mass, in kg.(2) The following are examples of symbols and required markings: (i) For a steel Large Packaging suitable for stacking; stacking load: 2,500 kg; maximum gross mass: 1,000 kg. View Image
(ii) For a plastic Large Packaging not suitable for stacking; maximum gross mass: 800 kg. View Image
(iii) For a Flexible Large Packaging not suitable for stacking; maximum gross mass: 500 kg. View Image
(iv) For a steel Large Salvage Packaging suitable for stacking; stacking load: 2,500 kg; maximum gross mass: 1,000 kg. View Image
(b) All Large Packagings manufactured, repaired or remanufactured after January 1, 2015 must be marked with the symbol applicable to a Large Packaging designed for stacking or not designed for stacking, as appropriate. The symbol must be a square with each side being not less than 100 mm (3.9 inches) by 100 mm (3.9 inches) as measured from the corner printer marks shown on the following figures. Where dimensions are not specified, all features must be in approximate proportion to those shown. View Image
(1)Transitional exception -A marking in conformance with the requirements of this paragraph in effect on December 31, 2014, may continue to be applied to all Large Packagings manufactured, repaired or remanufactured between January 1, 2015 and December 31, 2016.(2) For domestic transportation, a Large Packaging marked prior to January 1, 2017 and in conformance with the requirements of this paragraph in effect on December 31, 2014, may continue in service until the end of its useful life. 75 FR 5397 , Feb. 2, 2010, as amended at 75 FR 60339 , Sept. 30, 2010; 78 FR 1097 , Jan. 7, 2013; 80 FR 1168 , Jan. 8, 2015