Section 95110 - Cement ProductionThe operator of a facility who is required to report under section 95101 of this article, and who is not eligible for abbreviated reporting under section 95103(a), must comply with Subpart H of 40 CFR Part 98 (§§ 98.80 to 98.88) in reporting annual stationary combustion and process emissions and other data from cement production to ARB, except as otherwise provided in this section.
(a) CO2from Fossil Fuel Combustion. When calculating CO2 emissions from fuel combustion, the operator must use a method in 40 CFR § 98.33(a)(1) to § 98.33(a)(4) as specified by fuel type in section 95115 of this article.(b)Monitoring, Data and Records. For each emissions calculation method chosen under section 95110(a), the operator must meet the applicable requirements for monitoring, missing data procedures, data reporting, and records retention that are specified in 40 CFR § 98.34 to § 98.37, except as modified in sections 95110(c)-(d), 95115, and 95129 of this article.(c)Missing Data Substitution Procedures. The operator must comply with 40 CFR § 98.85 when substituting for missing data, except as otherwise provided in paragraphs (1)-(3) below. (1) To substitute for missing data for emissions reported under section 95115 of this article (stationary combustion units and units using continuous emissions monitoring systems), the operator must follow the requirements of section 95129 of this article.(2) If data for the carbonate content of clinker or cement kiln dust as required by 40 CFR § 98.83(d) are missing, and a new analysis cannot be undertaken, the operator must apply a substitute value according to the procedures in paragraphs (A)-(C) below. (A) If the data capture rate is at least 90 percent for the data year, the operator must substitute for each missing value using the best available estimate of the parameter, based on all available process data.(B) If the data capture rate is at least 80 percent but not at least 90 percent for the data year, the operator must substitute for each missing value with the highest quality assured value recorded for the parameter during the given data year, as well as the two previous data years.(C) If the data capture rate is less than 80 percent for the data year, the operator must substitute for each missing value with the highest quality assured value recorded for the parameter in all records kept according to section 95105(a).(3) For each missing value of the monthly raw material consumption or monthly clinker production used to calculate emissions, the operator must apply a substitute value according to paragraphs (A)-(B) below.(A) If the data capture rate is at least 80 percent for the data year, the operator must substitute for each missing value according to 40 CFR § 98.85(c) or 40 CFR § 98.85(d), as applicable.(B) If the data capture rate is less than 80 percent for the data year, the operator must substitute for each missing value with the maximum short tons of clinker per day capacity of the system or the maximum short tons per day raw material throughput of the kiln, as applicable, and the number of days per month.(4) The operator must document and retain records of the procedure used for all missing data estimates pursuant to the recordkeeping requirements of section 95105.(d)Additional Product Data. In addition to the information required by 40 CFR § 98.86, the operator must report the parameters provided in paragraphs (1)-(4) below whether or not a CEMS is used to measure CO2 emissions. (1) Annual quantity clinker produced (short tons).(2) Annual quantity clinker consumed (short tons).(3) Annual quantity of limestone and gypsum (including both natural and synthetic gypsum) consumed for blending (short tons).(4) Annual quantity of cement substitute consumed, by type (short tons). This parameter is not subject to review for material misstatement under the requirements of section 95131(b)(12).Cal. Code Regs. Tit. 17, § 95110
1. New subarticle 2 (sections 95110-95115) and section filed 12-2-2008; operative 1-1-2009 (Register 2008, No. 49).
2. Amendment of subarticle heading, repealer and new section heading and section and amendment of NOTE filed 12-14-2011; operative 1-1-2012 pursuant to Government Code section 11343.4 (Register 2011, No. 50).
3. Amendment of subsection (c) filed 12-31-2013; operative 1-1-2014 pursuant to Government Code section 11343.4(b)(3) (Register 2014, No. 1). Note: Authority cited: Sections 38510, 38530, 39600, 39601, 39607, 39607.4 and 41511, Health and Safety Code. Reference: Sections 38530, 39600 and 41511, Health and Safety Code.
1. New subarticle 2 (sections 95110-95115) and section filed 12-2-2008; operative 1-1-2009 (Register 2008, No. 49).
2. Amendment of subarticle heading, repealer and new section heading and section and amendment of Note filed 12-14-2011; operative 1-1-2012 pursuant to Government Code section 11343.4 (Register 2011, No. 50).
3. Amendment of subsection (c) filed 12-31-2013; operative 1-1-2014 pursuant to Government Code section 11343.4(b)(3) (Register 2014, No. 1).