Hazardous Waste Management System; Identification and Listing of Hazardous Waste Final Exclusion

AGENCY:

Environmental Protection Agency (EPA).

ACTION:

Final rule.

SUMMARY:

The EPA (also, “the Agency” or “we” in this preamble) is granting a petition to exclude (or “delist”) wastewater treatment plant sludge from conversion coating on aluminum generated by the Ford Motor Company Dearborn Truck Assembly Plant (DTP) in Dearborn, Michigan from the list of hazardous wastes.

Today's action conditionally excludes the petitioned waste from the requirements of hazardous waste regulations under the Resource Conservation and Recovery Act (RCRA) when disposed of in a lined subtitle D landfill which is permitted, licensed, or registered by a State to manage industrial solid waste. The exclusion was proposed on March 7, 2002 as part of an expedited process to evaluate this waste under a pilot project developed with the Michigan Department of Environmental Quality (MDEQ). The rule also imposes testing conditions for waste generated in the future to ensure that this waste continues to qualify for delisting.

DATES:

This rule is effective on April 25, 2005.

ADDRESSES:

EPA has established a docket for this action under Docket ID No. R5-MIECOS-01. All documents in the docket are listed in the index. Publicly available docket materials are available in hard copy at the U.S. EPA Region 5, 77 W. Jackson Blvd., Chicago, IL 60604. This Docket Facility is open from 8 a.m. to 4 p.m., Monday through Friday, excluding Federal holidays. The public may copy material from the regulatory docket at $0.15 per page. Contact Judy Kleiman for appointments at the address above, by email at kleiman.judy@epa.gov or by calling (312) 886-1482.

FOR FURTHER INFORMATION CONTACT:

For technical information concerning this document, contact Judy Kleiman, Waste, Pesticides, and Toxics Division, (Mail Code: DW-8J), U.S. EPA Region 5, 77 W. Jackson Blvd., Chicago, IL 60604; telephone number: (312) 886-1482; fax number: (312) 353-4788; e-mail address: kleiman.judy@epa.gov.

SUPPLEMENTARY INFORMATION:

The information in this section is organized as follows:

I. Background

A. What is a delisting petition?

B. What regulations allow a waste to be delisted?

C. What waste did DTP petition to delist?

II. The Expedited Process for Delisting

A. Why was the expedited process developed for this waste?

B. What is the expedited process to delist F019?

III. EPA's Evaluation of This Petition

A. What information was submitted in support of this petition?

B. How did EPA evaluate the information submitted?

IV. Public Comments Received on the Proposed Expedited Process

A. Who submitted comments on the proposed rule?

B. Comments received and responses from EPA

V. Final Rule Granting These Petitions

A. What decision is EPA finalizing?

B. What are the terms of this exclusion?

C. When is the delisting effective?

D. How does this action affect the states?

VI. Statutory and Executive Order Reviews

I. Background

A. What Is a Delisting Petition?

A delisting petition is a request from a generator to exclude waste from the list of hazardous wastes under RCRA regulations. In a delisting petition, the petitioner must show that waste generated at a particular facility does not meet any of the criteria for which EPA listed the waste as set forth in title 40 Code of Federal Regulations (40 CFR) 261.11 and the background document for the waste. In addition, a petitioner must demonstrate that the waste does not exhibit any of the hazardous waste characteristics (that is, ignitability, reactivity, corrosivity, and toxicity) and must present sufficient information for us to decide whether factors other than those for which the waste was listed warrant retaining it as a hazardous waste. (See 40 CFR 260.22, 42 U.S.C. 6921(f) and the background documents for a listed waste.)

Generators remain obligated under RCRA to confirm that their waste remains nonhazardous based on the hazardous waste characteristics even if EPA has “delisted” the wastes and to ensure that future generated wastes meet the conditions set.

B. What Regulations Allow a Waste To Be Delisted?

Under 40 CFR 260.20, 260.22, and 42 U.S.C. 6921(f), facilities may petition the EPA to remove their wastes from hazardous waste control by excluding them from the lists of hazardous wastes contained in 40 CFR 261.31 and 261.32. Specifically, 40 CFR 260.20 allows any person to petition the Administrator to modify or revoke any provision of parts 260 through 266, 268, and 273 of 40 CFR. 40 CFR 260.22 provides a generator the opportunity to petition the Administrator to exclude a waste from the lists of hazardous wastes on a “generator specific” basis.

C. What Waste Did DTP Petition To Delist?

DTP petitioned to exclude wastewater treatment sludge resulting from a zinc phosphating conversion coating process on truck bodies which have aluminum components. When treated, the wastewater from the conversion coating on aluminum results in a listed waste, F019. The wastewater from the phosphating process entering the wastewater treatment plant combines with wastewaters from other operations at the plant including cleaning and rinsing operations, electrocoating processes, vehicle leak testing, and floor scrubbing. Wastewaters include alkaline cleaners, surfactants, organic detergents, rinse conditioners from cleaning operations and overflows and rinse water from electrocoating. All sludge from the treatment of this wastewater is regulated as RCRA hazardous waste F019.

II. The Expedited Process for Delisting

A. Why Was the Expedited Process Developed for This Waste?

Automobile manufacturers are adding aluminum components to automobile and light truck bodies. When aluminum is conversion coated in a zinc phosphating process in automobile assembly plants, the resulting wastewater treatment sludge must be managed as EPA hazardous waste F019. F019 wastes generated at other auto assembly plants using the same zinc phosphating and wastewater treatment processes have been shown to be nonhazardous.

This similarity of manufacturing processes and the resultant wastes provides an opportunity for the automobile industry to be more efficient in submitting delisting petitions and for EPA to be more efficient in evaluating them. Efficiency may be gained and time saved by using a standardized approach for gathering, submitting and evaluating data. Therefore, EPA, in conjunction with MDEQ, developed a pilot project to expedite the delisting process. This approach to making delisting determinations for this group of facilities is efficient while still being consistent with current laws and regulations and protective of human health and the environment.

By removing regulatory controls under RCRA, EPA is facilitating the use of aluminum in cars. EPA believes that incorporating aluminum in cars will be advantageous to the environment since lighter cars are capable of achieving better fuel economy.

B. What Is the Expedited Process To Delist F019?

The expedited process to delist F019 is an approach developed through a Memorandum of Understanding (MOU) with MDEQ for gathering and evaluating data in support of multiple petitions from automobile assembly plants. The expedited delisting process is applicable to wastes generated by automobile and light truck assembly plants in the State of Michigan which use a similar manufacturing process and generate similar F019 waste.

Based on available historical data and other information, the expedited process identified 70 constituents which might be of concern in the waste and provides that the F019 sludge generated by automobile assembly plants may be delisted if the levels of the 70 constituents do not exceed the allowable levels established for each constituent in this rulemaking. The maximum annual quantity of waste generated by any single facility which may be covered by an expedited delisting is 3,000 cubic yards. Delisting levels were also proposed for smaller quantities of 1,000 and 2,000 cubic yards.

III. EPA's Evaluation of This Petition

A. What Information Was Submitted in Support of This Petition?

DTP submitted certification that its process was the same as the process described in the MOU between Region 5 and MDEQ. See 67 FR 10341, March 7, 2002. The facility also asserted that its waste does not meet the criteria for which F019 waste was listed and there are no other factors which might cause the waste to be hazardous.

To support its exclusion demonstration, Ford Dearborn collected six samples representing waste generated over a seven week period. Each sample was analyzed for: (1) Total analyses of 69 constituents of concern; (2) Toxicity Characteristic Leaching Procedure (TCLP), SW-846 Method 1311, analyses of 69 constituents of concern; (3) oil and grease; and (4) total constituent analyses for sulfide and cyanide. In addition, the pH of each sample was measured and a determination was made that the waste was not ignitable, corrosive or reactive (see 40 CFR 261.21-261.23). With the exception of the minor change noted here, all sampling and analyses were done in accordance with the sampling and analysis plan which is an appendix to the MOU and is available in the docket for this rule. Instead of sampling directly from six different roll-off boxes which would have required multiple sampling events or long-term storage of full roll-off boxes, DTP collected representative amounts of sludge each week from June 8 through July 27, 2004. The sludge for each week was placed in a separate drum. On July 27, 2004, composite and grab samples were collected from each of the six drums.

The maximum values of constituents detected in any sample of the waste and in a TCLP extract of that waste are summarized in the following table. The data submitted included the appropriate QA/QC information validated by a third party.

B. How Did EPA Evaluate the Information Submitted?

EPA compared the analytical results submitted by DTP to the maximum allowable levels calculated by the DRAS and set forth in the proposed rule (67 FR 10341, March 7, 2002). The maximum allowable levels for constituents detected in the waste or a TCLP extract of the waste are summarized in the table above, along with the observed levels. The table also includes the maximum allowable levels in groundwater at a potential receptor well, as evaluated by the Delisting Risk Assessment Software (DRAS). These levels are the more conservative of either the Safe Drinking Water Act Maximum Contaminant Level (MCL) or the health-based value calculated by DRAS based on the target cancer risk level of 10^{− 6}. For arsenic, the target cancer risk was set at 10^{− 4} in consideration of the MCL and the potential for natural occurrence. The maximum allowable groundwater concentration and delisting level for arsenic correspond to a drinking water concentration less than one half the current MCL of 10 μg/L.

EPA also used the DRAS program to estimate the aggregate cancer risk and hazard index for constituents detected in the waste. The aggregate cancer risk is the cumulative total of all individual constituent cancer risks. The hazard index is a similar cumulative total of non-cancer effects. The target aggregate cancer risk is 1×10^{− 5} and the target hazard index is one. The wastewater treatment plant sludge at DTP met both of these criteria.

IV. Public Comments Received on the Proposed Exclusion

A. Who Submitted Comments on the Proposed Rule?

The EPA received public comments on the proposed notice published on March 7, 2002 from Alliance of Automobile Manufacturers, Honda of America Mfg., Inc., Alcoa Inc., and The Aluminum Association. All commenters were supportive of the proposal and suggested expanding the project and revising the listing.

B. Comments Received and Responses From EPA

(1) Comment: EPA should revise the F019 listing to specify that wastewater treatment sludge from zinc phosphating operations is not within the scope of the listing. Data gathered as a result of the Expedited Delisting Project together with the available historical data, should provide enough data to fully characterize this waste and to justify a revision of the listing.

EPA Response: The Agency is now considering revising the F019 listing. EPA is examining the data collected as a result of this project, as well as past data, as a basis for a possible revision to the F019 listing.

(2) Comment: EPA should issue an interpretive rule clarifying that zinc phosphating operations are outside the scope of the F019 listing.

EPA Response: An interpretive rule presents administrative and technical difficulties. A revision to the listing will require a rulemaking process. See response to comment (1) above.

(3) Comment: Automobile assembly facilities outside of Michigan would like to take advantage of the precedent set by this expedited delisting project to delist F019 generated by similar operations in other states and regions.

EPA Response: The Agency believes that the expedited delisting procedures and requirements set forth in this proposal are appropriate for similar automotive assembly facilities outside the State of Michigan, subject to the discretion of the regulatory agency (state or region).

(4) Comment: Alternatives to landfilling like recycling should be allowed within the petition process.

EPA Response: The Agency does not delist wastes which are recycled because the model used to estimate risk is based only on disposal of waste in a subtitle D landfill. The risk which might result from any other scenario is not evaluated by the delisting program. However, the Agency encourages safe recycling, and variances and exclusions from the definition of solid and hazardous wastes are available for wastes which are recycled.

(5) Comment: Analytical methods should be specified in the pre-approved common sampling plan instead of requiring each participant to submit a site-specific list of methods.

EPA Response: Allowing the petitioner to choose an analytical method which meets the data quality objectives specific to the delisting petition provides flexibility. Data quality objectives will vary depending on the allowable levels which are a function of the volume of petitioned waste. The Agency believes that the flexibility of performance based methods results in better data.

(6) Comment: Detection limits should not be required prior to sampling since they cannot be adequately predicted without a way to estimate matrix effects.

EPA Response: Although matrix effects cannot be assessed in advance of laboratory analysis, a laboratory should be able to provide estimated detection levels and reporting levels which are lower than, or at least equal to, the allowable delisting level for each constituent.

(7) Comment: Since the process generating the sludge is extremely stable, verification sampling should be conducted on an annual, instead of quarterly, basis. The requirement that any process change be promptly reported and the exclusion suspended until EPA gives written approval that the delisting can continue is an adequate safeguard justifying the decrease in sample event frequency.

EPA Response: Verification data submitted in conjunction with past delistings of this waste have shown significant variation on a quarterly basis over longer periods of time. Annual sampling would not detect such variations. Once enough verification data are collected to support a statistical analysis, a change in the frequency of verification sampling and/or sampling parameters may be considered.

(8) Comment: The final Federal Register should make it clear that assembly plants that manufacture light trucks are also eligible for the project.

EPA Response: Today's notice specifically defines eligible facilities as inclusive of manufacturers of light trucks.

(9) Comment: The table of maximum allowable levels in the March 7, 2002 proposed rule contains errors in the columns for vinyl chloride.

EPA Response: The error was caused by a missing space or tab in the table. The maximum allowable concentrations proposed for 2,000 cubic yards of waste should have been 115 mg/kg total and 0.00234 mg/L TCLP.

V. Final Rule Granting These Petitions

A. What Decision Is EPA Finalizing?

Today the EPA is finalizing an exclusion to conditionally delist an annual volume of 2,000 cubic yards of wastewater treatment plant sludge generated at DTP from conversion coating on aluminum.

On March 7, 2002, EPA proposed to exclude or delist this wastewater treatment sludge from the list of hazardous wastes in 40 CFR 261.31 and accepted public comment on the proposed rule (67 FR 10341). EPA considered all comments received, and we believe that this waste should be excluded from hazardous waste control.

B. What Are the Terms of This Exclusion?

DTP must dispose of the waste in a lined subtitle D landfill which is permitted, licensed, or registered by a state to manage industrial solid waste. DTP must obtain and analyze on a quarterly basis a representative sample of the waste in accordance with the waste analysis plan. DTP must verify that the concentrations of the constituents of concern do not exceed the allowable levels set forth in this exclusion. The list of constituents for verification is a subset of those initially tested for and is based on the occurrence of constituents at the majority of facilities participating in the expedited process to delist F019 and the concentrations detected relative to the allowable levels.

This exclusion applies only to a maximum annual volume of 2,000 cubic yards and is effective only if all conditions contained in this rule are satisfied.

C. When Is the Delisting Effective?

This rule is effective April 25, 2005. The Hazardous and Solid Waste Amendments of 1984 amended section 3010 of RCRA to allow rules to become effective in less than six months when the regulated community does not need the six-month period to come into compliance. This rule reduces rather than increases the existing requirements and, therefore, is effective immediately upon publication under the Administrative Procedure Act, pursuant to 5 U.S.C. 553(d).

D. How Does This Action Affect the States?

Today's exclusion is being issued under the Federal RCRA delisting program. Therefore, only states subject to Federal RCRA delisting provisions would be affected. This exclusion is not effective in states which have received authorization to make their own delisting decisions. Also, the exclusion may not be effective in states having a dual system that includes Federal RCRA requirements and their own requirements. EPA allows states to impose their own regulatory requirements that are more stringent than EPA's, under section 3009 of RCRA. These more stringent requirements may include a provision that prohibits a federally issued exclusion from taking effect in the state. Because a dual system (that is, both Federal (RCRA) and state (non-RCRA) programs) may regulate a petitioner's waste, we urge petitioners to contact the state regulatory authority to establish the status of their wastes under the state law. If a participating facility transports the petitioned waste to or manages the waste in any state with delisting authorization, it must obtain a delisting from that state before it can manage the waste as nonhazardous in the state.

VI. Statutory and Executive Order Reviews

Under Executive Order 12866, “Regulatory Planning and Review” (58 FR 51735, October 4, 1993), this rule is not of general applicability and therefore is not a regulatory action subject to review by the Office of Management and Budget (OMB). This rule does not impose an information collection burden under the provisions of the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.) because it applies to a particular facility only. Because this rule is of particular applicability relating to a particular facility, it is not subject to the regulatory flexibility provisions of the Regulatory Flexibility Act (5 U.S.C. 601 et seq.), or to sections 202, 204, and 205 of the Unfunded Mandates Reform Act of 1995 (UMRA) (Pub. L. 104-4). Because this rule will affect only a particular facility, it will not significantly or uniquely affect small governments, as specified in section 203 of UMRA.

Because this rule will affect only a particular facility, this final rule does not have federalism implications. It will not have substantial direct effects on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government, as specified in Executive Order 13132, “Federalism,” (64 FR 43255, August 10, 1999). Thus, Executive Order 13132 does not apply to this rule. Similarly, because this rule will affect only a particular facility, this final rule does not have tribal implications, as specified in Executive Order 13175, “Consultation and Coordination with Indian Tribal Governments” (65 FR 67249, November 9, 2000). Thus, Executive Order 13175 does not apply to this rule.

This rule also is not subject to Executive Order 13045, “Protection of Children from Environmental Health Risks and Safety Risks” (62 FR 19885, April 23, 1997), because it is not economically significant as defined in Executive Order 12866, and because the Agency does not have reason to believe the environmental health or safety risks addressed by this action present a disproportionate risk to children. The basis for this belief is that the Agency used the DRAS program, which considers health and safety risks to infants and children, to calculate the maximum allowable concentrations for this rule.

This rule is not subject to Executive Order 13211, “Actions Concerning Regulations That Significantly Affect Energy Supply, Distribution, or Use” (66 FR 28355 (May 22, 2001)), because it is not a significant regulatory action under Executive Order 12866.

This rule does not involve technical standards; thus, the requirements of section 12(d) of the National Technology Transfer and Advancement Act of 1995 (15 U.S.C. 272 note) do not apply.

As required by section 3 of Executive Order 12988, “Civil Justice Reform,” (61 FR 4729, February 7, 1996), in issuing this rule, EPA has taken the necessary steps to eliminate drafting errors and ambiguity, minimize potential litigation, and provide a clear legal standard for affected conduct.

The Congressional Review Act, 5 U.S.C. 801 et seq., as added by the Small Business Regulatory Enforcement Fairness Act of 1996, generally provides that before a rule may take effect, the agency promulgating the rule must submit a rule report which includes a copy of the rule to each House of the Congress and to the Comptroller General of the United States. Section 804 exempts from section 801 the following types of rules (1) rules of particular applicability; (2) rules relating to agency management or personnel; and (3) rules of agency organization, procedure, or practice that do not substantially affect the rights or obligations of non-agency parties 5 U.S.C. 804(3). EPA is not required to submit a rule report regarding today's action under section 801 because this is a rule of particular applicability.

List of Subjects in 40 CFR Part 261

• Environmental protection
• Hazardous waste
• Recycling, and Reporting and recordkeeping requirements

Authority: Sec. 3001(f) RCRA, 42 U.S.C. 6921(f).

For the reasons set out in the preamble, 40 CFR part 261 is proposed to be amended as follows:

PART 261—IDENTIFICATION AND LISTING OF HAZARDOUS WASTE

1. The authority citation for part 261 continues to read as follows:

Authority: 42 U.S.C. 6905, 6912(a), 6921, 6922, and 6938.

2. In Table 1 of appendix IX of part 261 the following wastestreams are added in alphabetical order by facility to read as follows:

Appendix IX to Part 261—Wastes Excluded Under §§ 260.20 and 260.22