Certain Corrosion-Resistant Steel Products From Italy: Final Results of the Expedited First Sunset Review of the Countervailing Duty Order

AGENCY:

Enforcement and Compliance, International Trade Administration, Department of Commerce.

SUMMARY:

The Department of Commerce (Commerce) finds that revocation of the countervailing duty (CVD) order on certain corrosion-resistant steel products (corrosion-resistant steel) from Italy would be likely to lead to continuation or recurrence of countervailing subsidies at the levels indicated in the “Final Results of Sunset Review” section of this notice.

DATES:

Applicable September 28, 2021.

FOR FURTHER INFORMATION CONTACT:

Robert Scully, AD/CVD Operations, Office V, Enforcement and Compliance, International Trade Administration, U.S. Department of Commerce, 1401 Constitution Avenue NW, Washington, DC 20230; telephone: (202) 482-0572.

SUPPLEMENTARY INFORMATION:

Background

On July 25, 2016, Commerce published in the Federal Register the CVD order on corrosion-resistant steel from Italy. On June 1, 2021, Commerce published the notice of initiation of the first sunset review of the Order, pursuant to section 751(c) of the Tariff Act of 1930, as amended (the Act). On June 14 and 16, 2021, Commerce received timely filed notices of intent to participate from Cleveland-Cliffs, Inc., Nucor Corporation, Steel Dynamics Inc., California Steel Industries, and U.S. Steel Corporation (collectively, the domestic interested parties), within the deadline specified in 19 CFR 351.218(d)(1)(i). The domestic interested parties claimed interested party status under section 771(9)(C) of the Act as producers of the domestic like product in the United States.

On July 1, 2021, Commerce received an adequate substantive response from the domestic interested parties within the 30-day deadline specified in 19 CFR 351.218(d)(3)(i). We received no substantive responses from any other interested party, including the Government of Italy, nor was a hearing requested. On July 22, 2021, Commerce notified the U.S. International Trade Commission that it did not receive an adequate substantive response from respondent interested parties. As a result, pursuant to section 751(c)(3)(B) of the Act and 19 CFR 351.218(e)(1)(ii)(B)-(C), Commerce conducted an expedited (120-day) sunset review of the Order.

Scope of the Order

The products covered by this order are certain corrosion-resistant steel products. For a complete description of the scope of the Order, see Appendix I.

Analysis of Comments Received

All issues raised in this sunset review are addressed in the accompanying Issues and Decision Memorandum, which is hereby adopted by this notice. The issues discussed in the Issues and Decision Memorandum are listed in Appendix II. The Issues and Decision Memorandum is a public document and is on file electronically via Enforcement and Compliance's Antidumping and Countervailing Duty Centralized Electronic Service System (ACCESS). ACCESS is available to registered users at http://access.trade.gov. In addition, a complete version of the Issues and Decision Memorandum can be accessed directly at http://enforcement.trade.gov/frn/.

Final Results of Sunset Review

Pursuant to sections 751(c)(1) and 752(b) of the Act, Commerce determines that revocation of the Order would likely lead to continuation or recurrence of countervailable subsidies at the rates listed below.

Administrative Protective Order (APO)

This notice serves as the only reminder to interested parties subject to an APO of their responsibility concerning the return or destruction of proprietary information disclosed under APO in accordance with 19 CFR 351.305. Timely notification of the return or destruction of APO materials or conversion to judicial protective order is hereby requested. Failure to comply with the regulations and terms of an APO is a violation which is subject to sanction.

Notification to Interested Parties

We are issuing and publishing these final results and notice in accordance with sections 751(c), 752(b), and 777(i)(1) of the Act and 19 CFR 351.218.

Appendix I

Scope of the Order

The products covered by this order are certain flat-rolled steel products, either clad, plated, or coated with corrosion-resistant metals such as zinc, aluminum, or zinc-, aluminum-, nickel- or iron-based alloys, whether or not corrugated or painted, varnished, laminated, or coated with plastics or other non-metallic substances in addition to the metallic coating. The products covered include coils that have a width of 12.7 mm or greater, regardless of form of coil ( e.g., in successively superimposed layers, spirally oscillating, etc.). The products covered also include products not in coils ( e.g., in straight lengths) of a thickness less than 4.75 mm and a width that is 12.7 mm or greater and that measures at least 10 times the thickness. The products covered also include products not in coils ( e.g., in straight lengths) of a thickness of 4.75 mm or more and a width exceeding 150 mm and measuring at least twice the thickness. The products described above may be rectangular, square, circular, or other shape and include products of either rectangular or non-rectangular cross-section where such cross-section is achieved subsequent to the rolling process, i.e., products which have been “worked after rolling” ( e.g., products which have been beveled or rounded at the edges). For purposes of the width and thickness requirements referenced above:

(1) Where the nominal and actual measurements vary, a product is within the scope if application of either the nominal or actual measurement would place it within the scope based on the definitions set forth above, and

(2) where the width and thickness vary for a specific product ( e.g., the thickness of certain products with non-rectangular cross-section, the width of certain products with non-rectangular shape, etc.), the measurement at its greatest width or thickness applies.

Steel products included in the scope of this order are products in which: (1) Iron predominates, by weight, over each of the other contained elements; (2) the carbon content is 2 percent or less, by weight; and (3) none of the elements listed below exceeds the quantity, by weight, respectively indicated:

• 2.50 percent of manganese, or
• 3.30 percent of silicon, or
• 1.50 percent of copper, or
• 1.50 percent of aluminum, or
• 1.25 percent of chromium, or
• 0.30 percent of cobalt, or
• 0.40 percent of lead, or
• 2.00 percent of nickel, or
• 0.30 percent of tungsten (also called wolfram), or
• 0.80 percent of molybdenum, or
• 0.10 percent of niobium (also called columbium), or
• 0.30 percent of vanadium, or
• 0.30 percent of zirconium

Unless specifically excluded, products are included in this scope regardless of levels of boron and titanium.

For example, specifically included in this scope are vacuum degassed, fully stabilized (commonly referred to as interstitial-free (IF)) steels and high strength low alloy (HSLA) steels. IF steels are recognized as low carbon steels with micro-alloying levels of elements such as titanium and/or niobium added to stabilize carbon and nitrogen elements. HSLA steels are recognized as steels with micro-alloying levels of elements such as chromium, copper, niobium, titanium, vanadium, and molybdenum.

Furthermore, this scope also includes Advanced High Strength Steels (AHSS) and Ultra High Strength Steels (UHSS), both of which are considered high tensile strength and high elongation steels.

Subject merchandise also includes corrosion-resistant steel that has been further processed in a third country, including but not limited to annealing, tempering painting, varnishing, trimming, cutting, punching and/or slitting or any other processing that would not otherwise remove the merchandise from the scope of the Order if performed in the country of manufacture of the in-scope corrosion resistant steel.

All products that meet the written physical description, and in which the chemistry quantities do not exceed any one of the noted element levels listed above, are within the scope of this order unless specifically excluded. The following products are outside of and/or specifically excluded from the scope of this order:

• Flat-rolled steel products either plated or coated with tin, lead, chromium, chromium oxides, both tin and lead (“terne plate”), or both chromium and chromium oxides (“tin free steel”), whether or not painted, varnished or coated with plastics or other non-metallic substances in addition to the metallic coating;
• Clad products in straight lengths of 4.7625 mm or more in composite thickness and of a width which exceeds 150 mm and measures at least twice the thickness; and
• Certain clad stainless flat-rolled products, which are three-layered corrosion-resistant flat-rolled steel products less than 4.75 mm in composite thickness that consist of a flat-rolled steel product clad on both sides with stainless steel in a 20%-60%-20% ratio.

The products subject to the Order are currently classified in the Harmonized Tariff Schedule of the United States (HTSUS) under item numbers: 7210.30.0030, 7210.30.0060, 7210.41.0000, 7210.49.0030, 7210.49.0091, 7210.49.0095, 7210.61.0000, 7210.69.0000, 7210.70.6030, 7210.70.6060, 7210.70.6090, 7210.90.6000, 7210.90.9000, 7212.20.0000, 7212.30.1030, 7212.30.1090, 7212.30.3000, 7212.30.5000, 7212.40.1000, 7212.40.5000, 7212.50.0000, 7212.60.0000, 7210.49.0040, and 7210.49.0045.

The products subject to the Order may also enter under the following HTSUS item numbers: 7210.90.1000, 7215.90.1000, 7215.90.3000, 7215.90.5000, 7217.20.1500, 7217.30.1530, 7217.30.1560, 7217.90.1000, 7217.90.5030, 7217.90.5060, 7217.90.5090, 7225.91.0000, 7225.92.0000, 7225.99.0090, 7226.99.0110, 7226.99.0130, 7226.99.0180, 7228.60.6000, 7228.60.8000, and 7229.90.1000.

The HTSUS subheadings above are provided for convenience and customs purposes only. The written description of the scope of the Order is dispositive.

Appendix II

List of Topics Discussed in the Issues and Decision Memorandum

I. Summary

II. Background

III. Scope of the Order

IV. History of the Order

V. Legal Framework

VI. Discussion of the Issues

1. Likelihood of Continuation or Recurrence of a Countervailable Subsidy

2. Net Countervailable Subsidy Rate Likely to Prevail

3. Nature of the Subsidies

VII. Final Results of Review

VIII. Recommendation