Airworthiness Directives; Dassault Aviation Airplanes

AGENCY:

Federal Aviation Administration (FAA), Department of Transportation (DOT).

ACTION:

Final rule.

SUMMARY:

We are adopting a new airworthiness directive (AD) for certain Dassault Aviation Model FALCON 7X airplanes. This AD was prompted by a report of improperly drilled bores, located on upper and lower stiffener joints to the Web at a certain frame. This AD requires a one-time inspection of the bores, and repair if necessary. We are issuing this AD to detect and correct an unsatisfactory bore that can adversely affect the structural integrity of the airplane.

DATES:

This AD is effective August 16, 2016.

The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of August 16, 2016.

ADDRESSES:

For service information identified in this final rule, contact Dassault Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South Hackensack, NJ 07606; telephone: 201-440-6700; Internet: http://www.dassaultfalcon.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221. It is also available on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-3987.

Examining the AD Docket

You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-3987; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (telephone 800-647-5527) is Docket Management Facility, U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT:

Tom Rodriguez, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1137; fax 425-227-1149.

SUPPLEMENTARY INFORMATION:

Discussion

We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to certain Dassault Aviation Model FALCON 7X airplanes. The NPRM published in the Federal Register on March 1, 2016 (81 FR 10535) (“the NPRM”).

The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Union, has issued Airworthiness Directive 2015-0204, dated October 8, 2015 (referred to after this as the Mandatory Continuing Airworthiness Information, or “the MCAI”), to correct an unsafe condition for certain Dassault Aviation FALCON 7X airplanes. The MCAI states:

On the assembly line of Falcon 7X airplanes, defects were detected on left hand and right hand engine pylons. A quality review revealed that bores located on upper and lower stiffener joints to the web at pylon Frame 41 were improperly drilled. Fettlings of borings, for fixing diameter 4 mm [millimeters] and 5 mm, were found ovalized, too deep and having irregular surface qualities under the head of fixing. Dassault Aviation identified the individual airplanes that are potentially affected by this production deficiency.

This condition, if not detected and corrected, would adversely affect the structural integrity of the airplane.

To address this potential unsafe condition Dassault Aviation published Service Bulletin (SB) 7X-346 to provide corrective action instructions.

For the reasons described above, this [EASA] AD requires a one-time [detailed] visual [and rototest] inspection for unsatisfactory bores and, depending on findings, repair of affected stiffener bores.

A bore is not satisfactory if it has any surface defects greater than or equal to 0.5 mm or if any chamfer dimension or edge distance value is not within the dimensions specified in Dassault Aviation Service Bulletin 7X-346, dated April 24, 2015. You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-3987.

Comments

We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM or on the determination of the cost to the public.

Conclusion

We reviewed the relevant data and determined that air safety and the public interest require adopting this AD with the changes described previously except for minor editorial changes. We have determined that these minor changes:

• Are consistent with the intent that was proposed in the NPRM for correcting the unsafe condition; and
• Do not add any additional burden upon the public than was already proposed in the NPRM.

Related Service Information Under 1 CFR Part 51

We reviewed Dassault Service Bulletin 7X-346, dated April 24, 2015. The service information describes procedures for a one-time inspection and repair of the bores on stiffeners at Frame 41 on the engine pylons.

This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section.

Costs of Compliance

We estimate that this AD affects 55 airplanes of U.S. registry.

We estimate the following costs to comply with this AD:

We estimate the following costs to do any necessary repair that would be required based on the results of the required inspection. We have no way of determining the number of airplanes that might need this repair:

According to the manufacturer, some of the costs of this AD may be covered under warranty, thereby reducing the cost impact on affected individuals. We do not control warranty coverage for affected individuals. As a result, we have included all costs in our cost estimate.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, Section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

1. Is not a “significant regulatory action” under Executive Order 12866;

2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);

3. Will not affect intrastate aviation in Alaska; and

4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

• Air transportation
• Aircraft
• Aviation safety
• Incorporation by reference
• Safety

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39—AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD):

2016-13-15 Dassault Aviation: Amendment 39-18580. Docket No. FAA-2016-3987; Directorate Identifier 2015-NM-165-AD.

(a) Effective Date

This AD is effective August 16, 2016.

(b) Affected ADs

None.

(c) Applicability

This AD applies to Dassault Aviation Model FALCON 7X airplanes, certificated in any category, manufacturer serial numbers 1 through 221 inclusive, except serial numbers 182 and 220.

(d) Subject

Air Transport Association (ATA) of America Code 53, Fuselage.

(e) Reason

This AD was prompted by a report of improperly drilled bores, located on upper and lower stiffener joints to the web at a certain frame. We are issuing this AD to detect and correct an unsatisfactory bore that can adversely affect the structural integrity of the airplane.

(f) Compliance

Comply with this AD within the compliance times specified, unless already done.

(g) Inspect Bores

Within 4,000 flight cycles or 98 months, whichever occurs first since date of issuance of the original airworthiness certificate or date of issuance of the original export certificate of airworthiness, do a detailed visual and rototest inspection of the bores, located on upper and lower stiffener joints to the web at pylon Frame 41, to determine if the bores are not satisfactory, in accordance with the Accomplishment Instructions of Dassault Service Bulletin 7X-346, dated April 24, 2015.

(h) Repair

If, during the inspection required by paragraph (g) of this AD, it is determined that any bore is not satisfactory: Before further flight, repair affected bores, in accordance with the Accomplishment Instructions of Dassault Service Bulletin 7X-346, dated April 24, 2015, except as required by paragraph (i) of this AD.

(i) Exceptions

Where the Dassault Service Bulletin 7X-346, dated April 24, 2015, specifies to contact Dassault Aviation: Before further flight, repair using a method approved by the Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA; or the European Aviation Safety Agency (EASA); or Dassault Aviation's EASA Design Organization Approval (DOA).

(j) Other FAA AD Provisions

The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Branch, send it to ATTN: Tom Rodriguez, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1137; fax 425-227-1149. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. The AMOC approval letter must specifically reference this AD.

(2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA; or EASA; or Dassault Aviation's EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature.

(k) Related Information

Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA AD 2015-0204, dated October 8, 2015, for related information. This MCAI may be found on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-3987.

(l) Material Incorporated by Reference

(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise.

(i) Dassault Service Bulletin 7X-346, dated April 24, 2015.

(ii) Reserved.

(3) For service information identified in this AD, contact Dassault Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South Hackensack, NJ 07606; telephone: 201-440-6700; Internet: http://www.dassaultfalcon.com.

(4) You may view this service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221.

(5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.